summaryrefslogtreecommitdiffstatshomepage
path: root/src/mess/drivers/cat.c
diff options
context:
space:
mode:
Diffstat (limited to 'src/mess/drivers/cat.c')
-rw-r--r--src/mess/drivers/cat.c20
1 files changed, 10 insertions, 10 deletions
diff --git a/src/mess/drivers/cat.c b/src/mess/drivers/cat.c
index d5e51e66185..27543b3f780 100644
--- a/src/mess/drivers/cat.c
+++ b/src/mess/drivers/cat.c
@@ -223,7 +223,7 @@ J4: 18-pin sip header for keyboard ribbon cable; bottom edge of board is pin 1
Pins:
1: GND through 220k resistor r78
2: ? phone hook related? anode of diode d7; one of the pins of relay k2; topmost (boardwise) pin of transistor Q10
- 3: 74HCT34 pin
+ 3: 74HCT34 pin
J5: locking-tab-type "CONN HEADER VERT 4POS .100 TIN" connector for supplying power
through a small cable with a berg connector at the other end, to the floppy drive
@@ -240,7 +240,7 @@ J9: unpopulated DIL 40-pin straight connector for a ROM debug/expansion/RAM-shad
/HICE is !a15
/ROM_OE comes from pin 14 of DECODE_E pal, and is shorted to /ROM_OE' by the cuttable jumper B1 which is not cut
/ROM_OE' goes to the two EPROMS
- DECODE_18 is DECODE_E pal pin 18
+ DECODE_18 is DECODE_E pal pin 18
pin 1 (GND) is in the lower left and the pins count low-high then to the right
(gnd N/C E_CLK R/W /ROM_OE a17 vcc a14 a13 a8 a9 a11 /ROM_OE' a10 a15 d7 d6 d5 d4 d3 )
(GND /IPL1 DECODE_18 /RESET gnd a16 vcc a12 a7 a6 a5 a4 a3 a2 a1 a0 d0 d1 d2 gnd)
@@ -369,10 +369,10 @@ ToDo:
// pin 13 (PB3) :
// pin 14 (PB4) :
// pin 15 (PB5) :
-// pin 16 (PB6) :
+// pin 16 (PB6) :
// pin 17 (PB7) :
-// pin 18 (CB1) : ?from/to? Floppy connector j3 pin 8
-// pin 19 (CB2) : ?from/to? 6522 @ u35 pin 16 (PB6)
+// pin 18 (CB1) : ?from/to? Floppy connector j3 pin 8
+// pin 19 (CB2) : ?from/to? 6522 @ u35 pin 16 (PB6)
// pin 21 (/IRQ) : out to 68008 /IPL1 pin 41
// pin 22 (R/W) : in from 68008 R/W pin 30
// pin 23 (/CS2) : in from DECODE E pin 18
@@ -384,7 +384,7 @@ ToDo:
// pin 39 (CA2) is through inductor L11 and resistor r128 to peripheral connector pin 35 <end minus 26>
// pin 40 (CA1) is through inductor L30 and resistor r138 to peripheral connector pin 53 <end minus 8>
-// 6522 @ u35
+// 6522 @ u35
// pin 2 (PA0) :
// pin 3 (PA1) :
// pin 4 (PA2) :
@@ -421,9 +421,9 @@ ToDo:
// pin 4 (Y2) : out to 6522 @u35 pin 11
// pin 5 (A2) : in from 4N37 @ u48 pin 5 (output side emitter pin) (tied via R189 to gnd) <ring indicator?>
// pin 6 (B2) : in from 4N37 @ u48 pin 5 (output side emitter pin) (tied via R189 to gnd) <ring indicator?>
-// pin 8 (B3) :
-// pin 9 (A3) :
-// pin 10 (Y3) :
+// pin 8 (B3) :
+// pin 9 (A3) :
+// pin 10 (Y3) :
// pin 11 (B4) : in from 68008 A15
// pin 12 (A4) : in from 68008 A15
// pin 13 (Y4) : out to EPROM @ U31 /CE
@@ -1743,7 +1743,7 @@ ROM_START( swyft )
* ||||\-------------Q? ?
* |||\--------------Q? ?
* ||\---------------Q> output to decode pal pin 2
- * |\----------------->? output? to ram multiplexer 'A' pins
+ * |\----------------->? output? to ram multiplexer 'A' pins
* \------------------< ?
*/
ROM_LOAD( "timing_b.ampal16r4a.u9.jed", 0x0000, 0xb08, CRC(643e6e83) SHA1(7db167883f9d6cf385ce496d08976dc16fc3e2c3))