// license:BSD-3-Clause // copyright-holders:Michael Zapf /* Cycle-precise implementation of the TMS9980A. Subclassed from tms99xx_device in tms9900.c. +----------------+ /HOLD | 1 \/ 40| /MEMEN HOLDA | 2 39| READY IAQ | 3 38| /WE LSB +- A13,CRUOUT | 4 37| CRUCLK | A12 | 5 36| Vdd | A11 | 6 35| Vss | A10 | 7 34| CKIN Address A9 | 8 33| D7 --+ bus A8 | 9 32| D6 | | A7 |10 31| D5 Data 16KiB A6 |11 30| D4 bus | A5 |12 29| D3 | | A4 |13 28| D2 2 * 8 bit | A3 |14 27| D1 | | A2 |15 26| D0 --+ | A1 |16 25| INT0 --+ MSB +-- A0 |17 24| INT1 | Interrupt levels DBIN |18 23| INT2 --+ CRUIN |19 22| /PHI3 Vcc |20 21| Vbb +----------------+ The TMS9980A is similar to the TMS9900, with the following differences: - Address bus is only 14 bit wide (16 KiB) - Data bus is 16 bit wide and multiplexed on 8 lines (2 bytes per access) - CRU space is limited to 2048 bits (due to fewer address lines) - Only three interrupt level lines, for a maximum of 8 levels. - No INTREQ, RESET, and LOAD lines. All interrupts are signaled via INT0 - INT2. Reset=00x, Load=010, Level1=011, Level2=100, Level3=101, Level4=110, all interrupts cleared=111. - Memory accesses are always 2 bytes (even address byte, odd address byte) even for byte operations. Thus the 9980A, like the TMS9900, needs to pre-fetch the word at the destination before overwriting it. - On the cycle level both TMS9900 and TMS9980A are equal, except for the additional cycles needed for memory read and write access. Accordingly, the emulation shares the core and the microprograms and redefines the memory access and the interrupt handling only. - The 9980A has the same external instructions as the TMS9900, but it indicates the command via A0, A1, and A13 (instead of A0-A2). For pin definitions see tms9900.c Michael Zapf, 2012 */ #include "tms9980a.h" #define LOG logerror #define VERBOSE 1 /**************************************************************************** Constructor ****************************************************************************/ tms9980a_device::tms9980a_device(const machine_config &mconfig, const char *tag, device_t *owner, UINT32 clock) : tms99xx_device(mconfig, TMS9980A, "TMS9980A", tag, 8, 14, 11, owner, clock, "tms9980a", __FILE__) { } /* External connections */ void tms9980a_device::resolve_lines() { const tms9980a_config *conf = reinterpret_cast(static_config()); assert (conf != NULL); // Resolve our external connections m_external_operation.resolve(conf->external_callback, *this); m_iaq_line.resolve(conf->instruction_acquisition, *this); m_clock_out_line.resolve(conf->clock_out, *this); m_holda_line.resolve(conf->holda_line, *this); m_dbin_line.resolve(conf->dbin_line, *this); } UINT16 tms9980a_device::read_workspace_register_debug(int reg) { int temp = m_icount; int addr = (WP+(reg<<1)) & 0xfffe & m_prgaddr_mask; UINT16 value = (m_prgspace->read_byte(addr) << 8) | (m_prgspace->read_byte(addr+1) & 0xff); m_icount = temp; return value; } void tms9980a_device::write_workspace_register_debug(int reg, UINT16 data) { int temp = m_icount; int addr = (WP+(reg<<1)) & 0xfffe & m_prgaddr_mask; m_prgspace->write_byte(addr, data>>8); m_prgspace->write_byte(addr+1, data & 0xff); m_icount = temp; } /* Interrupt input. Keep in mind that the TMS9980A does not have any INTREQ line but signals interrupts via IC0-IC2 only. Thus we cannot take down any single interrupt; only all interrupts can be cleared at once using level 7. The state parameter is actually not needed. */ void tms9980a_device::execute_set_input(int irqline, int state) { // We model the three lines IC0-IC2 as 8 separate input lines, although we // cannot assert more than one at a time. The state value is not needed, // as level 7 means to clean all interrupts, but we consider it for the // sake of consistency. int level = irqline; // Just to stay consistent. if (state==CLEAR_LINE) level = INT_9980A_CLEAR; switch (level) { case INT_9980A_RESET: case 1: level = RESET_INT; m_reset = true; break; case INT_9980A_LOAD: level = LOAD_INT; break; case INT_9980A_LEVEL1: case INT_9980A_LEVEL2: case INT_9980A_LEVEL3: case INT_9980A_LEVEL4: level = level - 2; break; case INT_9980A_CLEAR: // Clear all interrupts m_load_state = false; m_irq_state = false; if (VERBOSE>6) LOG("tms9980a: clear interrupts\n"); break; } m_irq_level = level; if (m_irq_level != INT_9980A_CLEAR) { if (m_irq_level == LOAD_INT) { // Some boards start up with LOAD interrupt, so we clear the reset flag m_reset = false; m_load_state = true; } else m_irq_state = true; if (VERBOSE>6) LOG("tms9980a: interrupt level=%d, ST=%04x\n", m_irq_level, ST); } } /*****************************************************************************/ /* Memory read: Clock cycles: 4 + 2W, W = number of wait states */ void tms9980a_device::mem_read() { UINT8 value; switch (m_mem_phase) { case 1: m_pass = 4; // make the CPU visit this method more than once m_dbin_line(ASSERT_LINE); m_prgspace->set_address(m_address & m_prgaddr_mask & ~1); if (VERBOSE>7) LOG("tms9980a: set address bus %04x\n", m_address & m_prgaddr_mask & ~1); m_check_ready = true; break; case 2: // Sample the value on the data bus (high byte) value = m_prgspace->read_byte(m_address & m_prgaddr_mask & ~1); if (VERBOSE>7) LOG("tms9980a: memory read high byte %04x -> %02x\n", m_address & m_prgaddr_mask & ~1, value); m_current_value = (value << 8) & 0xff00; break; case 3: m_prgspace->set_address((m_address & m_prgaddr_mask) | 1); if (VERBOSE>7) LOG("tms9980a: set address bus %04x\n", (m_address & m_prgaddr_mask) | 1); break; case 4: // Sample the value on the data bus (low byte) value = m_prgspace->read_byte((m_address & m_prgaddr_mask) | 1); m_current_value = m_current_value | (value & 0x00ff); if (VERBOSE>7) LOG("tms9980a: memory read low byte %04x -> %02x -> complete word %04x\n", (m_address & m_prgaddr_mask) | 1, value, m_current_value); break; } pulse_clock(1); m_mem_phase = (m_mem_phase % 4) +1; } void tms9980a_device::mem_write() { switch (m_mem_phase) { case 1: m_pass = 4; // make the CPU visit this method once more m_dbin_line(CLEAR_LINE); m_prgspace->set_address(m_address & m_prgaddr_mask & ~1); if (VERBOSE>7) LOG("tms9980a: set address bus %04x\n", m_address & m_prgaddr_mask & ~1); m_prgspace->write_byte(m_address & 0x3ffe & ~1, (m_current_value >> 8)&0xff); if (VERBOSE>7) LOG("tms9980a: memory write high byte %04x <- %02x\n", m_address & m_prgaddr_mask & ~1, (m_current_value >> 8)&0xff); m_check_ready = true; break; case 2: // no action here, just wait for READY break; case 3: m_prgspace->set_address((m_address & m_prgaddr_mask) | 1); if (VERBOSE>7) LOG("tms9980a: set address bus %04x\n", (m_address & m_prgaddr_mask) | 1); m_prgspace->write_byte((m_address & m_prgaddr_mask) | 1, m_current_value & 0xff); if (VERBOSE>7) LOG("tms9980a: memory write low byte %04x <- %02x\n", (m_address & m_prgaddr_mask) | 1, m_current_value & 0xff); break; case 4: // no action here, just wait for READY break; } pulse_clock(1); m_mem_phase = (m_mem_phase % 4) +1; } void tms9980a_device::acquire_instruction() { if (m_mem_phase == 1) { m_iaq_line(ASSERT_LINE); m_address = PC; m_first_cycle = m_icount; } mem_read(); if (m_mem_phase == 1) // changed by mem_read and wrapped { decode(m_current_value); if (VERBOSE>3) LOG("tms9980a: ===== Next operation %04x (%s) at %04x =====\n", IR, opname[m_command], PC); debugger_instruction_hook(this, PC); PC = (PC + 2) & 0xfffe & m_prgaddr_mask; } // IAQ will be cleared in the main loop } /**************************************************************************/ UINT32 tms9980a_device::execute_min_cycles() const { return 2; } // TODO: Compute this value, just a wild guess for the average UINT32 tms9980a_device::execute_max_cycles() const { return 10; } UINT32 tms9980a_device::execute_input_lines() const { return 8; } // clocks to cycles, cycles to clocks = id // execute_default_irq_vector = 0 // execute_burn = nop // device_disasm_interface overrides UINT32 tms9980a_device::disasm_min_opcode_bytes() const { return 2; } UINT32 tms9980a_device::disasm_max_opcode_bytes() const { return 6; } offs_t tms9980a_device::disasm_disassemble(char *buffer, offs_t pc, const UINT8 *oprom, const UINT8 *opram, UINT32 options) { extern CPU_DISASSEMBLE( tms9980 ); return CPU_DISASSEMBLE_NAME(tms9980)(this, buffer, pc, oprom, opram, options); } const device_type TMS9980A = &device_creator;