summaryrefslogtreecommitdiffstatshomepage
path: root/src/mame/drivers/mcr.c
diff options
context:
space:
mode:
Diffstat (limited to 'src/mame/drivers/mcr.c')
-rw-r--r--src/mame/drivers/mcr.c384
1 files changed, 192 insertions, 192 deletions
diff --git a/src/mame/drivers/mcr.c b/src/mame/drivers/mcr.c
index f52f52b8928..808563a10fc 100644
--- a/src/mame/drivers/mcr.c
+++ b/src/mame/drivers/mcr.c
@@ -309,16 +309,16 @@ static UINT8 nflfoot_serial_in_numbits;
WRITE8_MEMBER(mcr_state::mcr_control_port_w)
{
/*
- Bit layout is as follows:
- D7 = n/c
- D6 = cocktail flip
- D5 = red LED
- D4 = green LED
- D3 = n/c
- D2 = coin meter 3
- D1 = coin meter 2
- D0 = coin meter 1
- */
+ Bit layout is as follows:
+ D7 = n/c
+ D6 = cocktail flip
+ D5 = red LED
+ D4 = green LED
+ D3 = n/c
+ D2 = coin meter 3
+ D1 = coin meter 2
+ D0 = coin meter 1
+ */
coin_counter_w(machine(), 0, (data >> 0) & 1);
coin_counter_w(machine(), 1, (data >> 1) & 1);
@@ -519,10 +519,10 @@ READ8_MEMBER(mcr_state::kroozr_ip1_r)
WRITE8_MEMBER(mcr_state::kroozr_op4_w)
{
/*
- bit 2 = ship control
- bit 4 = cargo light cntl 1
- bit 5 = cargo light cntl 2
- */
+ bit 2 = ship control
+ bit 4 = cargo light cntl 1
+ bit 5 = cargo light cntl 2
+ */
}
@@ -582,50 +582,50 @@ WRITE8_MEMBER(mcr_state::twotiger_op4_w)
WRITE8_MEMBER(mcr_state::dotron_op4_w)
{
/*
- Flasher Control:
- A 555 timer is set up in astable mode with R1=R2=56k and C=1uF giving
- a frequency of 8.5714 Hz. The timer is enabled if J1-3 is high (1).
- The output of the timer is connected to the input of a D-type flip
- flop at 1A, which is clocked by the AC sync (since this is a
- fluorescent light fixture).
-
- The J1-4 input is also connected the input of another D-type flip flop
- on the same chip at 1A. The output of this directly controls the light
- fixture.
-
- Thus:
- J1-3 enables a strobe effect at 8.5714 Hz (77.616ms high, 38.808ms low)
- J1-4 directly enables/disables the lamp.
- The two outputs are wire-ored together.
- */
+ Flasher Control:
+ A 555 timer is set up in astable mode with R1=R2=56k and C=1uF giving
+ a frequency of 8.5714 Hz. The timer is enabled if J1-3 is high (1).
+ The output of the timer is connected to the input of a D-type flip
+ flop at 1A, which is clocked by the AC sync (since this is a
+ fluorescent light fixture).
+
+ The J1-4 input is also connected the input of another D-type flip flop
+ on the same chip at 1A. The output of this directly controls the light
+ fixture.
+
+ Thus:
+ J1-3 enables a strobe effect at 8.5714 Hz (77.616ms high, 38.808ms low)
+ J1-4 directly enables/disables the lamp.
+ The two outputs are wire-ored together.
+ */
/* bit 7 = FL1 (J1-3) on flasher control board */
/* bit 6 = FL0 (J1-4) on flasher control board */
output_set_value("backlight", (data >> 6) & 1);
/*
- Lamp Sequencer:
- A 556 timer is set up in astable mode with two different frequencies,
- one using R1=R2=10k and C=10uF giving a frequency of 4.8 Hz, and the
- second using R1=R2=5.1k and C=10uF giving a frequency of 9.4118 Hz.
+ Lamp Sequencer:
+ A 556 timer is set up in astable mode with two different frequencies,
+ one using R1=R2=10k and C=10uF giving a frequency of 4.8 Hz, and the
+ second using R1=R2=5.1k and C=10uF giving a frequency of 9.4118 Hz.
- The outputs of these clocks go into a mux at U4, whose input is
- selected by the input bit latched from J1-6.
+ The outputs of these clocks go into a mux at U4, whose input is
+ selected by the input bit latched from J1-6.
- The output of the mux clocks a 16-bit binary counter at U3. The
- output of the binary counter becomes the low 4 address bits of the
- 82S123 PROM at U2. The upper address bit comes from the input bit
- latched from J1-5.
+ The output of the mux clocks a 16-bit binary counter at U3. The
+ output of the binary counter becomes the low 4 address bits of the
+ 82S123 PROM at U2. The upper address bit comes from the input bit
+ latched from J1-5.
- Each of the 5 output bits from the 82S123 is inverted and connected
- to one of the lamps. The /CE pin on the 82S123 is connected to the
- input bit latched from J1-4.
+ Each of the 5 output bits from the 82S123 is inverted and connected
+ to one of the lamps. The /CE pin on the 82S123 is connected to the
+ input bit latched from J1-4.
- Thus:
- J1-4 enables (0) or disables (1) the lamp sequencing.
- J1-5 selects one of two 16-entry sequences stored in the 82S123.
- J1-6 selects one of two speeds (0=4.8 Hz, 1=9.4118 Hz)
+ Thus:
+ J1-4 enables (0) or disables (1) the lamp sequencing.
+ J1-5 selects one of two 16-entry sequences stored in the 82S123.
+ J1-6 selects one of two speeds (0=4.8 Hz, 1=9.4118 Hz)
- */
+ */
/* bit 5 = SEL1 (J1-1) on the Lamp Sequencer board */
if (((last_op4 ^ data) & 0x20) && (data & 0x20))
{
@@ -874,7 +874,7 @@ ADDRESS_MAP_END
/* verified from wiring diagram, plus DIP switches from manual */
static INPUT_PORTS_START( solarfox )
- PORT_START("ssio:IP0") /* J4 1-8 */
+ PORT_START("ssio:IP0") /* J4 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_COIN1 )
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_COIN2 )
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_BUTTON2 )
@@ -884,7 +884,7 @@ static INPUT_PORTS_START( solarfox )
PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_SERVICE1 )
PORT_SERVICE( 0x80, IP_ACTIVE_LOW )
- PORT_START("ssio:IP1") /* J4 10-13,15-18 */
+ PORT_START("ssio:IP1") /* J4 10-13,15-18 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_JOYSTICK_RIGHT ) PORT_4WAY
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_JOYSTICK_LEFT ) PORT_4WAY
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_JOYSTICK_DOWN ) PORT_4WAY
@@ -894,11 +894,11 @@ static INPUT_PORTS_START( solarfox )
PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_JOYSTICK_DOWN ) PORT_4WAY PORT_COCKTAIL
PORT_BIT( 0x80, IP_ACTIVE_LOW, IPT_JOYSTICK_UP ) PORT_4WAY PORT_COCKTAIL
- PORT_START("ssio:IP2") /* J5 1-8 */
+ PORT_START("ssio:IP2") /* J5 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_BUTTON1 ) PORT_COCKTAIL
PORT_BIT( 0xfe, IP_ACTIVE_LOW, IPT_UNUSED )
- PORT_START("ssio:IP3") /* DIPSW @ B3 */
+ PORT_START("ssio:IP3") /* DIPSW @ B3 */
PORT_DIPNAME( 0x03, 0x03, "Bonus" )
PORT_DIPSETTING( 0x02, DEF_STR( None ) )
PORT_DIPSETTING( 0x03, "After 10 racks" )
@@ -915,7 +915,7 @@ static INPUT_PORTS_START( solarfox )
PORT_DIPSETTING( 0x80, DEF_STR( Upright ))
PORT_DIPSETTING( 0x00, DEF_STR( Cocktail ))
- PORT_START("ssio:IP4") /* J6 1-8 */
+ PORT_START("ssio:IP4") /* J6 1-8 */
PORT_BIT( 0xff, IP_ACTIVE_LOW, IPT_UNUSED )
PORT_START("ssio:DIP")
@@ -925,7 +925,7 @@ INPUT_PORTS_END
/* verified from wiring diagram, plus DIP switches from manual */
static INPUT_PORTS_START( kick )
- PORT_START("ssio:IP0") /* J4 1-8 */
+ PORT_START("ssio:IP0") /* J4 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_COIN1 )
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_COIN2 )
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_START1 )
@@ -935,19 +935,19 @@ static INPUT_PORTS_START( kick )
PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_SERVICE1 )
PORT_SERVICE( 0x80, IP_ACTIVE_LOW )
- PORT_START("ssio:IP1") /* J4 10-13,15-18 */
+ PORT_START("ssio:IP1") /* J4 10-13,15-18 */
PORT_BIT( 0xff, 0x00, IPT_DIAL ) PORT_SENSITIVITY(3) PORT_KEYDELTA(50) PORT_REVERSE
- PORT_START("ssio:IP2") /* J5 1-8 */
+ PORT_START("ssio:IP2") /* J5 1-8 */
PORT_BIT( 0xff, IP_ACTIVE_LOW, IPT_UNUSED )
- PORT_START("ssio:IP3") /* DIPSW @ B3 */
+ PORT_START("ssio:IP3") /* DIPSW @ B3 */
PORT_DIPNAME( 0x01, 0x00, "Music" )
PORT_DIPSETTING( 0x01, DEF_STR( Off ))
PORT_DIPSETTING( 0x00, DEF_STR( On ))
PORT_BIT( 0xfe, IP_ACTIVE_LOW, IPT_UNKNOWN )
- PORT_START("ssio:IP4") /* J6 1-8 */
+ PORT_START("ssio:IP4") /* J6 1-8 */
PORT_BIT( 0xff, IP_ACTIVE_LOW, IPT_UNUSED )
PORT_START("ssio:DIP")
@@ -960,7 +960,7 @@ INPUT_PORTS_END
/* verified from wiring diagram, plus DIP switches from manual */
static INPUT_PORTS_START( kickc )
- PORT_START("ssio:IP0") /* J4 1-8 */
+ PORT_START("ssio:IP0") /* J4 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_COIN1 )
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_COIN2 )
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_START1 )
@@ -970,14 +970,14 @@ static INPUT_PORTS_START( kickc )
PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_SERVICE1 )
PORT_SERVICE( 0x80, IP_ACTIVE_LOW )
- PORT_START("ssio:IP1") /* J4 10-13,15-18 */
+ PORT_START("ssio:IP1") /* J4 10-13,15-18 */
PORT_BIT( 0xff, 0x00, IPT_DIAL ) PORT_SENSITIVITY(3) PORT_KEYDELTA(50) PORT_REVERSE
- PORT_START("ssio:IP2") /* J5 1-8 */
+ PORT_START("ssio:IP2") /* J5 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_BUTTON1 ) PORT_COCKTAIL
PORT_BIT( 0xfe, IP_ACTIVE_LOW, IPT_UNUSED )
- PORT_START("ssio:IP3") /* DIPSW @ B3 */
+ PORT_START("ssio:IP3") /* DIPSW @ B3 */
PORT_DIPNAME( 0x01, 0x00, "Music" )
PORT_DIPSETTING( 0x01, DEF_STR( Off ))
PORT_DIPSETTING( 0x00, DEF_STR( On ))
@@ -987,7 +987,7 @@ static INPUT_PORTS_START( kickc )
PORT_DIPSETTING( 0x40, DEF_STR( Cocktail ))
PORT_BIT( 0x80, IP_ACTIVE_LOW, IPT_UNKNOWN )
- PORT_START("ssio:IP4") /* J6 1-8 */
+ PORT_START("ssio:IP4") /* J6 1-8 */
PORT_BIT( 0xff, IP_ACTIVE_LOW, IPT_UNKNOWN )
PORT_START("ssio:DIP")
@@ -1025,28 +1025,28 @@ static INPUT_PORTS_START( dpoker )
// 10-position DIP switch on the sound pcb
// settings and defaults are verified from a sticker inside the cabinet, I don't know where 9 or 10 are connected
PORT_START("ssio:IP3")
- PORT_DIPNAME( 0x01, 0x01, "Hopper" ) PORT_DIPLOCATION("B3:1")
+ PORT_DIPNAME( 0x01, 0x01, "Hopper" ) PORT_DIPLOCATION("B3:1")
PORT_DIPSETTING( 0x01, "Relay Pulse" )
PORT_DIPSETTING( 0x00, "Miser On" ) // what is this? - the game locks up if it's enabled
- PORT_DIPNAME( 0x02, 0x02, "Music" ) PORT_DIPLOCATION("B3:2")
+ PORT_DIPNAME( 0x02, 0x02, "Music" ) PORT_DIPLOCATION("B3:2")
PORT_DIPSETTING( 0x02, DEF_STR( On ) )
PORT_DIPSETTING( 0x00, DEF_STR( Off ) )
- PORT_DIPNAME( 0x04, 0x04, "Novelty" ) PORT_DIPLOCATION("B3:3")
+ PORT_DIPNAME( 0x04, 0x04, "Novelty" ) PORT_DIPLOCATION("B3:3")
PORT_DIPSETTING( 0x04, DEF_STR( On ) )
PORT_DIPSETTING( 0x00, DEF_STR( Off ) )
- PORT_DIPNAME( 0x08, 0x00, DEF_STR( Unused ) ) PORT_DIPLOCATION("B3:4")
+ PORT_DIPNAME( 0x08, 0x00, DEF_STR( Unused ) ) PORT_DIPLOCATION("B3:4")
PORT_DIPSETTING( 0x08, DEF_STR( On ) )
PORT_DIPSETTING( 0x00, DEF_STR( Off ) )
- PORT_DIPNAME( 0x10, 0x00, DEF_STR( Unused ) ) PORT_DIPLOCATION("B3:5")
+ PORT_DIPNAME( 0x10, 0x00, DEF_STR( Unused ) ) PORT_DIPLOCATION("B3:5")
PORT_DIPSETTING( 0x10, DEF_STR( On ) )
PORT_DIPSETTING( 0x00, DEF_STR( Off ) )
- PORT_DIPNAME( 0x20, 0x20, "Cards After 5th Coin" ) PORT_DIPLOCATION("B3:6")
+ PORT_DIPNAME( 0x20, 0x20, "Cards After 5th Coin" ) PORT_DIPLOCATION("B3:6")
PORT_DIPSETTING( 0x20, "Face Up" )
PORT_DIPSETTING( 0x00, "Logo Up" )
- PORT_DIPNAME( 0x40, 0x40, "Currency" ) PORT_DIPLOCATION("B3:7")
+ PORT_DIPNAME( 0x40, 0x40, "Currency" ) PORT_DIPLOCATION("B3:7")
PORT_DIPSETTING( 0x40, "Ike Dollars" )
PORT_DIPSETTING( 0x00, "Other Coins" )
- PORT_DIPNAME( 0x80, 0x00, "Background Color" ) PORT_DIPLOCATION("B3:8")
+ PORT_DIPNAME( 0x80, 0x00, "Background Color" ) PORT_DIPLOCATION("B3:8")
PORT_DIPSETTING( 0x80, "Green" )
PORT_DIPSETTING( 0x00, "Blue" )
// PORT_DIPNAME( 0x01, 0x00, DEF_STR( Unused ) ) PORT_DIPLOCATION("B3:9")
@@ -1089,7 +1089,7 @@ INPUT_PORTS_END
/* verified from wiring diagram, plus DIP switches from manual */
static INPUT_PORTS_START( shollow )
- PORT_START("ssio:IP0") /* J4 1-8 */
+ PORT_START("ssio:IP0") /* J4 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_COIN1 )
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_COIN2 )
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_START1 )
@@ -1099,7 +1099,7 @@ static INPUT_PORTS_START( shollow )
PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_SERVICE1 )
PORT_SERVICE( 0x80, IP_ACTIVE_LOW )
- PORT_START("ssio:IP1") /* J4 10-13,15-18 */
+ PORT_START("ssio:IP1") /* J4 10-13,15-18 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_JOYSTICK_LEFT ) PORT_2WAY
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_JOYSTICK_RIGHT ) PORT_2WAY
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_BUTTON2 )
@@ -1109,10 +1109,10 @@ static INPUT_PORTS_START( shollow )
PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_BUTTON2 ) PORT_COCKTAIL
PORT_BIT( 0x80, IP_ACTIVE_LOW, IPT_BUTTON1 ) PORT_COCKTAIL
- PORT_START("ssio:IP2") /* J5 1-8 */
+ PORT_START("ssio:IP2") /* J5 1-8 */
PORT_BIT( 0xff, IP_ACTIVE_LOW, IPT_UNUSED )
- PORT_START("ssio:IP3") /* DIPSW @ B3 */
+ PORT_START("ssio:IP3") /* DIPSW @ B3 */
PORT_DIPNAME( 0x01, 0x01, "Coin Meters" )
PORT_DIPSETTING( 0x01, "1" )
PORT_DIPSETTING( 0x00, "2" )
@@ -1121,7 +1121,7 @@ static INPUT_PORTS_START( shollow )
PORT_DIPSETTING( 0x02, DEF_STR( Cocktail ) )
PORT_BIT( 0xfc, IP_ACTIVE_LOW, IPT_UNKNOWN )
- PORT_START("ssio:IP4") /* J6 1-8 */
+ PORT_START("ssio:IP4") /* J6 1-8 */
PORT_BIT( 0xff, IP_ACTIVE_LOW, IPT_UNUSED )
PORT_START("ssio:DIP")
@@ -1131,7 +1131,7 @@ INPUT_PORTS_END
/* verified from wiring diagram, plus DIP switches from manual */
static INPUT_PORTS_START( tron )
- PORT_START("ssio:IP0") /* J4 1-8 */
+ PORT_START("ssio:IP0") /* J4 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_COIN1 )
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_COIN2 )
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_START1 )
@@ -1141,10 +1141,10 @@ static INPUT_PORTS_START( tron )
PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_SERVICE1 )
PORT_SERVICE( 0x80, IP_ACTIVE_LOW )
- PORT_START("ssio:IP1") /* J4 10-13,15-18 */
+ PORT_START("ssio:IP1") /* J4 10-13,15-18 */
PORT_BIT( 0xff, 0x00, IPT_DIAL ) PORT_SENSITIVITY(50) PORT_KEYDELTA(10) PORT_CODE_DEC(KEYCODE_Z) PORT_CODE_INC(KEYCODE_X) PORT_REVERSE
- PORT_START("ssio:IP2") /* J5 1-8 */
+ PORT_START("ssio:IP2") /* J5 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_JOYSTICK_LEFT ) PORT_8WAY
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_JOYSTICK_RIGHT ) PORT_8WAY
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_JOYSTICK_UP ) PORT_8WAY
@@ -1154,7 +1154,7 @@ static INPUT_PORTS_START( tron )
PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_JOYSTICK_UP ) PORT_8WAY PORT_COCKTAIL
PORT_BIT( 0x80, IP_ACTIVE_LOW, IPT_JOYSTICK_DOWN ) PORT_8WAY PORT_COCKTAIL
- PORT_START("ssio:IP3") /* DIPSW @ B3 */
+ PORT_START("ssio:IP3") /* DIPSW @ B3 */
PORT_DIPNAME( 0x01, 0x00, "Coin Meters" ) PORT_DIPLOCATION("SW1:1")
PORT_DIPSETTING( 0x01, "1" )
PORT_DIPSETTING( 0x00, "2" )
@@ -1173,7 +1173,7 @@ static INPUT_PORTS_START( tron )
// According to the manual, SW1 is a bank of *10* switches (9 is unused and 10 is freeze)
// Where are the values for the other two bits read?
- PORT_START("ssio:IP4") /* J6 1-8 */
+ PORT_START("ssio:IP4") /* J6 1-8 */
PORT_BIT( 0xff, 0x00, IPT_DIAL ) PORT_SENSITIVITY(50) PORT_KEYDELTA(10) PORT_REVERSE PORT_COCKTAIL
PORT_START("ssio:DIP")
@@ -1182,7 +1182,7 @@ static INPUT_PORTS_START( tron )
INPUT_PORTS_END
static INPUT_PORTS_START( tron3 )
- PORT_START("ssio:IP0") /* J4 1-8 */
+ PORT_START("ssio:IP0") /* J4 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_COIN1 )
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_COIN2 )
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_START1 )
@@ -1192,10 +1192,10 @@ static INPUT_PORTS_START( tron3 )
PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_SERVICE1 )
PORT_SERVICE( 0x80, IP_ACTIVE_LOW )
- PORT_START("ssio:IP1") /* J4 10-13,15-18 */
+ PORT_START("ssio:IP1") /* J4 10-13,15-18 */
PORT_BIT( 0xff, 0x00, IPT_DIAL ) PORT_SENSITIVITY(50) PORT_KEYDELTA(10) PORT_CODE_DEC(KEYCODE_Z) PORT_CODE_INC(KEYCODE_X) PORT_REVERSE
- PORT_START("ssio:IP2") /* J5 1-8 */
+ PORT_START("ssio:IP2") /* J5 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_JOYSTICK_LEFT ) PORT_8WAY
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_JOYSTICK_RIGHT ) PORT_8WAY
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_JOYSTICK_UP ) PORT_8WAY
@@ -1205,7 +1205,7 @@ static INPUT_PORTS_START( tron3 )
// PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_JOYSTICK_UP ) PORT_8WAY PORT_COCKTAIL
// PORT_BIT( 0x80, IP_ACTIVE_LOW, IPT_JOYSTICK_DOWN ) PORT_8WAY PORT_COCKTAIL
- PORT_START("ssio:IP3") /* DIPSW @ B3 */
+ PORT_START("ssio:IP3") /* DIPSW @ B3 */
PORT_DIPNAME( 0x01, 0x00, "Coin Meters" ) PORT_DIPLOCATION("SW1:1")
PORT_DIPSETTING( 0x01, "1" )
PORT_DIPSETTING( 0x00, "2" )
@@ -1224,7 +1224,7 @@ static INPUT_PORTS_START( tron3 )
// According to the manual, SW1 is a bank of *10* switches (9 is unused and 10 is freeze)
// Where are the values for the other two bits read?
- PORT_START("ssio:IP4") /* J6 1-8 */
+ PORT_START("ssio:IP4") /* J6 1-8 */
PORT_BIT( 0xff, IP_ACTIVE_LOW, IPT_UNKNOWN )
// PORT_BIT( 0xff, 0x00, IPT_DIAL ) PORT_SENSITIVITY(50) PORT_KEYDELTA(10) PORT_REVERSE PORT_COCKTAIL
@@ -1237,7 +1237,7 @@ INPUT_PORTS_END
/* verified from wiring diagram, plus DIP switches from manual */
static INPUT_PORTS_START( kroozr )
- PORT_START("ssio:IP0") /* J4 1-8 */
+ PORT_START("ssio:IP0") /* J4 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_COIN1 )
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_COIN2 )
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_START1 )
@@ -1247,25 +1247,25 @@ static INPUT_PORTS_START( kroozr )
PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_SERVICE1 )
PORT_SERVICE( 0x80, IP_ACTIVE_LOW )
- PORT_START("ssio:IP1") /* J4 10-13,15-18 */
- PORT_BIT( 0x07, IP_ACTIVE_HIGH, IPT_SPECIAL ) /* low 3 bits of spinner */
- PORT_BIT( 0x08, IP_ACTIVE_HIGH, IPT_SPECIAL ) /* sensor J1-10 */
- PORT_BIT( 0x10, IP_ACTIVE_HIGH, IPT_SPECIAL ) /* sensor J1-9 */
- PORT_BIT( 0x20, IP_ACTIVE_HIGH, IPT_SPECIAL ) /* sensor J1-8 */
- PORT_BIT( 0x40, IP_ACTIVE_HIGH, IPT_SPECIAL ) /* upper 1 bit of spinner */
+ PORT_START("ssio:IP1") /* J4 10-13,15-18 */
+ PORT_BIT( 0x07, IP_ACTIVE_HIGH, IPT_SPECIAL ) /* low 3 bits of spinner */
+ PORT_BIT( 0x08, IP_ACTIVE_HIGH, IPT_SPECIAL ) /* sensor J1-10 */
+ PORT_BIT( 0x10, IP_ACTIVE_HIGH, IPT_SPECIAL ) /* sensor J1-9 */
+ PORT_BIT( 0x20, IP_ACTIVE_HIGH, IPT_SPECIAL ) /* sensor J1-8 */
+ PORT_BIT( 0x40, IP_ACTIVE_HIGH, IPT_SPECIAL ) /* upper 1 bit of spinner */
PORT_BIT( 0x80, IP_ACTIVE_LOW, IPT_BUTTON2 )
- PORT_START("ssio:IP2") /* J5 1-8 */
+ PORT_START("ssio:IP2") /* J5 1-8 */
PORT_BIT( 0xff, 0x64, IPT_AD_STICK_X ) PORT_MINMAX(48,152) PORT_SENSITIVITY(100) PORT_KEYDELTA(52)
- PORT_START("ssio:IP3") /* DIPSW @ B3 */
+ PORT_START("ssio:IP3") /* DIPSW @ B3 */
PORT_BIT( 0x3f, IP_ACTIVE_LOW, IPT_UNKNOWN )
PORT_DIPNAME( 0x40, 0x00, DEF_STR( Cabinet ) )
PORT_DIPSETTING( 0x00, DEF_STR( Upright ) )
PORT_DIPSETTING( 0x40, DEF_STR( Cocktail ) )
PORT_BIT( 0x80, IP_ACTIVE_LOW, IPT_UNKNOWN )
- PORT_START("ssio:IP4") /* J6 1-8 */
+ PORT_START("ssio:IP4") /* J6 1-8 */
PORT_BIT( 0xff, 0x64, IPT_AD_STICK_Y ) PORT_MINMAX(48,152) PORT_SENSITIVITY(100) PORT_KEYDELTA(52)
PORT_START("ssio:DIP")
@@ -1278,7 +1278,7 @@ INPUT_PORTS_END
/* verified from wiring diagram, plus DIP switches from manual */
static INPUT_PORTS_START( domino )
- PORT_START("ssio:IP0") /* J4 1-8 */
+ PORT_START("ssio:IP0") /* J4 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_COIN1 )
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_COIN2 )
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_START1 )
@@ -1288,14 +1288,14 @@ static INPUT_PORTS_START( domino )
PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_SERVICE1 )
PORT_SERVICE( 0x80, IP_ACTIVE_LOW )
- PORT_START("ssio:IP1") /* J4 10-13,15-18 */
+ PORT_START("ssio:IP1") /* J4 10-13,15-18 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_JOYSTICK_LEFT ) PORT_4WAY
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_JOYSTICK_RIGHT ) PORT_4WAY
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_JOYSTICK_UP ) PORT_4WAY
PORT_BIT( 0x08, IP_ACTIVE_LOW, IPT_JOYSTICK_DOWN ) PORT_4WAY
PORT_BIT( 0xf0, IP_ACTIVE_LOW, IPT_UNUSED )
- PORT_START("ssio:IP2") /* J5 1-8 */
+ PORT_START("ssio:IP2") /* J5 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_JOYSTICK_LEFT ) PORT_4WAY PORT_COCKTAIL
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_JOYSTICK_RIGHT ) PORT_4WAY PORT_COCKTAIL
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_JOYSTICK_UP ) PORT_4WAY PORT_COCKTAIL
@@ -1303,7 +1303,7 @@ static INPUT_PORTS_START( domino )
PORT_BIT( 0x10, IP_ACTIVE_LOW, IPT_BUTTON1 ) PORT_COCKTAIL
PORT_BIT( 0xe0, IP_ACTIVE_LOW, IPT_UNUSED )
- PORT_START("ssio:IP3") /* DIPSW @ B3 */
+ PORT_START("ssio:IP3") /* DIPSW @ B3 */
PORT_DIPNAME( 0x01, 0x00, "Music" )
PORT_DIPSETTING( 0x01, DEF_STR( Off ))
PORT_DIPSETTING( 0x00, DEF_STR( On ))
@@ -1318,7 +1318,7 @@ static INPUT_PORTS_START( domino )
PORT_DIPSETTING( 0x80, "1" )
PORT_DIPSETTING( 0x00, "2" )
- PORT_START("ssio:IP4") /* J6 1-8 */
+ PORT_START("ssio:IP4") /* J6 1-8 */
PORT_BIT( 0xff, IP_ACTIVE_LOW, IPT_UNKNOWN )
PORT_START("ssio:DIP")
@@ -1328,7 +1328,7 @@ INPUT_PORTS_END
/* verified from wiring diagram, plus DIP switches from manual */
static INPUT_PORTS_START( journey )
- PORT_START("ssio:IP0") /* J4 1-8 */
+ PORT_START("ssio:IP0") /* J4 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_COIN1 )
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_COIN2 )
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_START1 )
@@ -1338,14 +1338,14 @@ static INPUT_PORTS_START( journey )
PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_SERVICE1 )
PORT_SERVICE( 0x80, IP_ACTIVE_LOW )
- PORT_START("ssio:IP1") /* J4 10-13,15-18 */
+ PORT_START("ssio:IP1") /* J4 10-13,15-18 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_JOYSTICK_LEFT ) PORT_4WAY
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_JOYSTICK_RIGHT ) PORT_4WAY
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_JOYSTICK_UP ) PORT_4WAY
PORT_BIT( 0x08, IP_ACTIVE_LOW, IPT_JOYSTICK_DOWN ) PORT_4WAY
PORT_BIT( 0xf0, IP_ACTIVE_LOW, IPT_UNUSED )
- PORT_START("ssio:IP2") /* J5 1-8 */
+ PORT_START("ssio:IP2") /* J5 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_JOYSTICK_LEFT ) PORT_4WAY PORT_COCKTAIL
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_JOYSTICK_RIGHT ) PORT_4WAY PORT_COCKTAIL
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_JOYSTICK_UP ) PORT_4WAY PORT_COCKTAIL
@@ -1353,7 +1353,7 @@ static INPUT_PORTS_START( journey )
PORT_BIT( 0x10, IP_ACTIVE_LOW, IPT_BUTTON1 ) PORT_COCKTAIL
PORT_BIT( 0xe0, IP_ACTIVE_LOW, IPT_UNUSED )
- PORT_START("ssio:IP3") /* DIPSW @ B3 */
+ PORT_START("ssio:IP3") /* DIPSW @ B3 */
PORT_DIPNAME( 0x01, 0x01, "Coin Meters" )
PORT_DIPSETTING( 0x01, "1" )
PORT_DIPSETTING( 0x00, "2" )
@@ -1362,7 +1362,7 @@ static INPUT_PORTS_START( journey )
PORT_DIPSETTING( 0x02, DEF_STR( Cocktail ) )
PORT_BIT( 0xfc, IP_ACTIVE_LOW, IPT_UNUSED )
- PORT_START("ssio:IP4") /* J6 1-8 */
+ PORT_START("ssio:IP4") /* J6 1-8 */
PORT_BIT( 0xff, IP_ACTIVE_LOW, IPT_UNKNOWN )
PORT_START("ssio:DIP")
@@ -1372,7 +1372,7 @@ INPUT_PORTS_END
/* verified from wiring diagram, plus DIP switches from manual */
static INPUT_PORTS_START( wacko )
- PORT_START("ssio:IP0") /* J4 1-8 */
+ PORT_START("ssio:IP0") /* J4 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_COIN1 )
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_COIN2 )
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_START1 )
@@ -1382,13 +1382,13 @@ static INPUT_PORTS_START( wacko )
PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_SERVICE1 )
PORT_SERVICE( 0x80, IP_ACTIVE_LOW )
- PORT_START("ssio:IP1") /* J4 10-13,15-18 */
+ PORT_START("ssio:IP1") /* J4 10-13,15-18 */
PORT_BIT( 0xff, 0x00, IPT_TRACKBALL_X ) PORT_SENSITIVITY(50) PORT_KEYDELTA(10)
- PORT_START("ssio:IP2") /* J5 1-8 */
+ PORT_START("ssio:IP2") /* J5 1-8 */
PORT_BIT( 0xff, 0x00, IPT_TRACKBALL_Y ) PORT_SENSITIVITY(50) PORT_KEYDELTA(10) PORT_REVERSE
- PORT_START("ssio:IP3") /* DIPSW @ B3 */
+ PORT_START("ssio:IP3") /* DIPSW @ B3 */
PORT_BIT( 0x3f, IP_ACTIVE_LOW, IPT_UNUSED )
PORT_DIPNAME( 0x40, 0x00, DEF_STR( Cabinet ) )
PORT_DIPSETTING( 0x00, DEF_STR( Upright ) )
@@ -1397,7 +1397,7 @@ static INPUT_PORTS_START( wacko )
PORT_DIPSETTING( 0x80, "1" )
PORT_DIPSETTING( 0x00, "2" )
- PORT_START("ssio:IP4") /* J6 1-8 */
+ PORT_START("ssio:IP4") /* J6 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_JOYSTICKLEFT_RIGHT ) PORT_4WAY
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_JOYSTICKLEFT_LEFT ) PORT_4WAY
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_JOYSTICKLEFT_DOWN ) PORT_4WAY
@@ -1420,7 +1420,7 @@ INPUT_PORTS_END
/* not verified, no manual found */
static INPUT_PORTS_START( twotiger )
- PORT_START("ssio:IP0") /* J4 1-8 */
+ PORT_START("ssio:IP0") /* J4 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_COIN1 )
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_COIN2 )
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_START2 )
@@ -1430,13 +1430,13 @@ static INPUT_PORTS_START( twotiger )
PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_SERVICE1 )
PORT_SERVICE( 0x80, IP_ACTIVE_LOW )
- PORT_START("ssio:IP1") /* J4 10-13,15-18 */
+ PORT_START("ssio:IP1") /* J4 10-13,15-18 */
PORT_BIT( 0xff, 0x67, IPT_AD_STICK_X ) PORT_MINMAX(0, 206) PORT_SENSITIVITY(100) PORT_KEYDELTA(10) PORT_PLAYER(2)
- PORT_START("ssio:IP2") /* J5 1-8 */
+ PORT_START("ssio:IP2") /* J5 1-8 */
PORT_BIT( 0xff, 0x67, IPT_AD_STICK_X ) PORT_MINMAX(0, 206) PORT_SENSITIVITY(100) PORT_KEYDELTA(10) PORT_PLAYER(1)
- PORT_START("ssio:IP3") /* DIPSW @ B3 */
+ PORT_START("ssio:IP3") /* DIPSW @ B3 */
PORT_DIPNAME( 0x01, 0x00, "Shot Speed" )
PORT_DIPSETTING( 0x01, "Fast" )
PORT_DIPSETTING( 0x00, "Slow" )
@@ -1445,7 +1445,7 @@ static INPUT_PORTS_START( twotiger )
PORT_DIPSETTING( 0x02, "2 Credits" )
PORT_BIT( 0xfc, IP_ACTIVE_LOW, IPT_UNUSED )
- PORT_START("ssio:IP4") /* J6 1-8 */
+ PORT_START("ssio:IP4") /* J6 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_BUTTON3 )
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_BUTTON2 )
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_BUTTON1 )
@@ -1461,7 +1461,7 @@ INPUT_PORTS_END
/* not verified, no manual found */
static INPUT_PORTS_START( twotigrc )
- PORT_START("ssio:IP0") /* J4 1-8 */
+ PORT_START("ssio:IP0") /* J4 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_COIN1 )
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_COIN2 )
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_START1 )
@@ -1471,20 +1471,20 @@ static INPUT_PORTS_START( twotigrc )
PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_SERVICE1 )
PORT_SERVICE( 0x80, IP_ACTIVE_LOW )
- PORT_START("ssio:IP1") /* J4 10-13,15-18 */
+ PORT_START("ssio:IP1") /* J4 10-13,15-18 */
PORT_BIT( 0xff, 0x00, IPT_DIAL ) PORT_SENSITIVITY(10) PORT_KEYDELTA(10) PORT_REVERSE
- PORT_START("ssio:IP2") /* J5 1-8 */
+ PORT_START("ssio:IP2") /* J5 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_BUTTON1 )
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_BUTTON2 )
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_BUTTON1 ) PORT_PLAYER(2)
PORT_BIT( 0x08, IP_ACTIVE_LOW, IPT_BUTTON2 ) PORT_PLAYER(2)
PORT_BIT( 0xf0, IP_ACTIVE_LOW, IPT_UNUSED )
- PORT_START("ssio:IP3") /* DIPSW @ B3 */
+ PORT_START("ssio:IP3") /* DIPSW @ B3 */
PORT_BIT( 0xff, IP_ACTIVE_LOW, IPT_UNUSED )
- PORT_START("ssio:IP4") /* J6 1-8 */
+ PORT_START("ssio:IP4") /* J6 1-8 */
PORT_BIT( 0xff, 0x00, IPT_DIAL ) PORT_SENSITIVITY(10) PORT_KEYDELTA(10) PORT_REVERSE PORT_PLAYER(2)
PORT_START("ssio:DIP")
@@ -1494,7 +1494,7 @@ INPUT_PORTS_END
/* verified from wiring diagram, plus DIP switches from manual */
static INPUT_PORTS_START( tapper )
- PORT_START("ssio:IP0") /* J4 1-8 */
+ PORT_START("ssio:IP0") /* J4 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_COIN1 )
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_COIN2 )
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_START1 )
@@ -1504,7 +1504,7 @@ static INPUT_PORTS_START( tapper )
PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_SERVICE1 )
PORT_SERVICE( 0x80, IP_ACTIVE_LOW )
- PORT_START("ssio:IP1") /* J4 10-13,15-18 */
+ PORT_START("ssio:IP1") /* J4 10-13,15-18 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_JOYSTICK_RIGHT ) PORT_4WAY
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_JOYSTICK_LEFT ) PORT_4WAY
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_JOYSTICK_DOWN ) PORT_4WAY
@@ -1512,7 +1512,7 @@ static INPUT_PORTS_START( tapper )
PORT_BIT( 0x10, IP_ACTIVE_LOW, IPT_BUTTON1 )
PORT_BIT( 0xe0, IP_ACTIVE_LOW, IPT_UNUSED )
- PORT_START("ssio:IP2") /* J5 1-8 */
+ PORT_START("ssio:IP2") /* J5 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_JOYSTICK_RIGHT ) PORT_4WAY PORT_COCKTAIL
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_JOYSTICK_LEFT ) PORT_4WAY PORT_COCKTAIL
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_JOYSTICK_DOWN ) PORT_4WAY PORT_COCKTAIL
@@ -1520,7 +1520,7 @@ static INPUT_PORTS_START( tapper )
PORT_BIT( 0x10, IP_ACTIVE_LOW, IPT_BUTTON1 ) PORT_COCKTAIL
PORT_BIT( 0xe0, IP_ACTIVE_LOW, IPT_UNUSED )
- PORT_START("ssio:IP3") /* DIPSW @ B3 */
+ PORT_START("ssio:IP3") /* DIPSW @ B3 */
PORT_BIT( 0x03, IP_ACTIVE_LOW, IPT_UNUSED )
PORT_DIPNAME( 0x04, 0x00, DEF_STR( Demo_Sounds ) )
PORT_DIPSETTING( 0x04, DEF_STR( Off ) )
@@ -1533,7 +1533,7 @@ static INPUT_PORTS_START( tapper )
PORT_DIPSETTING( 0x80, "1" )
PORT_DIPSETTING( 0x00, "2" )
- PORT_START("ssio:IP4") /* J6 1-8 */
+ PORT_START("ssio:IP4") /* J6 1-8 */
PORT_BIT( 0xff, IP_ACTIVE_LOW, IPT_UNUSED )
PORT_START("ssio:DIP")
@@ -1543,7 +1543,7 @@ INPUT_PORTS_END
/* not verified, no manual found */
static INPUT_PORTS_START( timber )
- PORT_START("ssio:IP0") /* J4 1-8 */
+ PORT_START("ssio:IP0") /* J4 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_COIN1 )
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_COIN2 )
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_START1 )
@@ -1553,7 +1553,7 @@ static INPUT_PORTS_START( timber )
PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_SERVICE1 )
PORT_SERVICE( 0x80, IP_ACTIVE_LOW )
- PORT_START("ssio:IP1") /* J4 10-13,15-18 */
+ PORT_START("ssio:IP1") /* J4 10-13,15-18 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_JOYSTICK_RIGHT ) PORT_4WAY PORT_PLAYER(1)
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_JOYSTICK_LEFT ) PORT_4WAY PORT_PLAYER(1)
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_JOYSTICK_DOWN ) PORT_4WAY PORT_PLAYER(1)
@@ -1562,7 +1562,7 @@ static INPUT_PORTS_START( timber )
PORT_BIT( 0x20, IP_ACTIVE_LOW, IPT_BUTTON2 ) PORT_PLAYER(1)
PORT_BIT( 0xc0, IP_ACTIVE_LOW, IPT_UNUSED )
- PORT_START("ssio:IP2") /* J5 1-8 */
+ PORT_START("ssio:IP2") /* J5 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_JOYSTICK_RIGHT ) PORT_4WAY PORT_PLAYER(2)
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_JOYSTICK_LEFT ) PORT_4WAY PORT_PLAYER(2)
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_JOYSTICK_DOWN ) PORT_4WAY PORT_PLAYER(2)
@@ -1571,7 +1571,7 @@ static INPUT_PORTS_START( timber )
PORT_BIT( 0x20, IP_ACTIVE_LOW, IPT_BUTTON2 ) PORT_PLAYER(2)
PORT_BIT( 0xc0, IP_ACTIVE_LOW, IPT_UNUSED )
- PORT_START("ssio:IP3") /* DIPSW @ B3 */
+ PORT_START("ssio:IP3") /* DIPSW @ B3 */
PORT_BIT( 0x03, IP_ACTIVE_LOW, IPT_UNUSED )
PORT_DIPNAME( 0x04, 0x00, DEF_STR( Demo_Sounds ) )
PORT_DIPSETTING( 0x04, DEF_STR( Off ) )
@@ -1584,7 +1584,7 @@ static INPUT_PORTS_START( timber )
PORT_DIPSETTING( 0x80, "1" )
PORT_DIPSETTING( 0x00, "2" )
- PORT_START("ssio:IP4") /* J6 1-8 */
+ PORT_START("ssio:IP4") /* J6 1-8 */
PORT_BIT( 0xff, IP_ACTIVE_LOW, IPT_UNUSED )
PORT_START("ssio:DIP")
@@ -1594,7 +1594,7 @@ INPUT_PORTS_END
/* verified from wiring diagram, plus DIP switches from manual */
static INPUT_PORTS_START( dotron )
- PORT_START("ssio:IP0") /* J4 1-8 */
+ PORT_START("ssio:IP0") /* J4 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_COIN1 )
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_COIN2 )
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_START1 )
@@ -1604,11 +1604,11 @@ static INPUT_PORTS_START( dotron )
PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_SERVICE1 )
PORT_SERVICE( 0x80, IP_ACTIVE_LOW )
- PORT_START("ssio:IP1") /* J4 10-13,15-18 */
+ PORT_START("ssio:IP1") /* J4 10-13,15-18 */
PORT_BIT( 0x7f, 0x00, IPT_DIAL ) PORT_SENSITIVITY(50) PORT_KEYDELTA(10) PORT_CODE_DEC(KEYCODE_Z) PORT_CODE_INC(KEYCODE_X) PORT_REVERSE
PORT_BIT( 0x80, IP_ACTIVE_LOW, IPT_UNUSED )
- PORT_START("ssio:IP2") /* J5 1-8 */
+ PORT_START("ssio:IP2") /* J5 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_JOYSTICK_LEFT ) PORT_8WAY
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_JOYSTICK_RIGHT ) PORT_8WAY
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_JOYSTICK_UP ) PORT_8WAY
@@ -1620,19 +1620,19 @@ static INPUT_PORTS_START( dotron )
PORT_DIPSETTING( 0x00, "Environmental" )
PORT_DIPSETTING( 0x80, DEF_STR( Upright ) )
- PORT_START("ssio:IP3") /* DIPSW @ B3 */
+ PORT_START("ssio:IP3") /* DIPSW @ B3 */
PORT_DIPNAME( 0x01, 0x01, "Coin Meters" )
PORT_DIPSETTING( 0x01, "1" )
PORT_DIPSETTING( 0x00, "2" )
PORT_BIT( 0xfe, IP_ACTIVE_LOW, IPT_UNUSED )
- PORT_START("ssio:IP4") /* J6 1-8 */
+ PORT_START("ssio:IP4") /* J6 1-8 */
PORT_BIT( 0xff, IP_ACTIVE_LOW, IPT_UNUSED )
PORT_START("ssio:DIP")
PORT_BIT( 0xff, IP_ACTIVE_LOW, IPT_UNKNOWN )
- PORT_START("FAKE") /* fake port to make aiming up & down easier */
+ PORT_START("FAKE") /* fake port to make aiming up & down easier */
PORT_BIT( 0xff, 0x00, IPT_TRACKBALL_Y ) PORT_SENSITIVITY(100) PORT_KEYDELTA(10)
INPUT_PORTS_END
@@ -1648,43 +1648,43 @@ INPUT_PORTS_END
/* verified from wiring diagram, plus DIP switches from manual */
static INPUT_PORTS_START( nflfoot )
- PORT_START("ssio:IP0") /* J4 1-8 */
+ PORT_START("ssio:IP0") /* J4 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_COIN1 )
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_BILL1 )
- PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_START2 ) /* continue game */
- PORT_BIT( 0x08, IP_ACTIVE_LOW, IPT_SERVICE1 ) /* service */
- PORT_BIT( 0x10, IP_ACTIVE_LOW, IPT_START1 ) /* new game */
+ PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_START2 ) /* continue game */
+ PORT_BIT( 0x08, IP_ACTIVE_LOW, IPT_SERVICE1 ) /* service */
+ PORT_BIT( 0x10, IP_ACTIVE_LOW, IPT_START1 ) /* new game */
PORT_BIT( 0x20, IP_ACTIVE_LOW, IPT_TILT )
PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_UNKNOWN )
PORT_SERVICE( 0x80, IP_ACTIVE_LOW )
- PORT_START("ssio:IP1") /* J4 10-13,15-18 */
- PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_BUTTON1 ) PORT_PLAYER(1) /* left engage */
- PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_BUTTON2 ) PORT_PLAYER(1) /* left select #1 play */
- PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_BUTTON3 ) PORT_PLAYER(1) /* left select #2 play */
- PORT_BIT( 0x08, IP_ACTIVE_LOW, IPT_BUTTON4 ) PORT_PLAYER(1) /* left select #3 play */
- PORT_BIT( 0x10, IP_ACTIVE_LOW, IPT_BUTTON5 ) PORT_PLAYER(1) /* left select #4 play */
- PORT_BIT( 0x20, IP_ACTIVE_LOW, IPT_BUTTON6 ) PORT_PLAYER(1) /* left select #5 play */
- PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_BUTTON7 ) PORT_PLAYER(1) /* select one player */
+ PORT_START("ssio:IP1") /* J4 10-13,15-18 */
+ PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_BUTTON1 ) PORT_PLAYER(1) /* left engage */
+ PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_BUTTON2 ) PORT_PLAYER(1) /* left select #1 play */
+ PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_BUTTON3 ) PORT_PLAYER(1) /* left select #2 play */
+ PORT_BIT( 0x08, IP_ACTIVE_LOW, IPT_BUTTON4 ) PORT_PLAYER(1) /* left select #3 play */
+ PORT_BIT( 0x10, IP_ACTIVE_LOW, IPT_BUTTON5 ) PORT_PLAYER(1) /* left select #4 play */
+ PORT_BIT( 0x20, IP_ACTIVE_LOW, IPT_BUTTON6 ) PORT_PLAYER(1) /* left select #5 play */
+ PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_BUTTON7 ) PORT_PLAYER(1) /* select one player */
PORT_BIT( 0x80, IP_ACTIVE_LOW, IPT_UNKNOWN )
- PORT_START("ssio:IP2") /* J5 1-8 */
- PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_BUTTON1 ) PORT_PLAYER(2) /* right engage */
- PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_BUTTON2 ) PORT_PLAYER(2) /* right select #1 play */
- PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_BUTTON3 ) PORT_PLAYER(2) /* right select #2 play */
- PORT_BIT( 0x08, IP_ACTIVE_LOW, IPT_BUTTON4 ) PORT_PLAYER(2) /* right select #3 play */
- PORT_BIT( 0x10, IP_ACTIVE_LOW, IPT_BUTTON5 ) PORT_PLAYER(2) /* right select #4 play */
- PORT_BIT( 0x20, IP_ACTIVE_LOW, IPT_BUTTON6 ) PORT_PLAYER(2) /* right select #5 play */
- PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_BUTTON7 ) PORT_PLAYER(2) /* select two player */
- PORT_BIT( 0x80, IP_ACTIVE_LOW, IPT_SPECIAL ) /* connects to IPU board */
-
- PORT_START("ssio:IP3") /* DIPSW @ B3 */
+ PORT_START("ssio:IP2") /* J5 1-8 */
+ PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_BUTTON1 ) PORT_PLAYER(2) /* right engage */
+ PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_BUTTON2 ) PORT_PLAYER(2) /* right select #1 play */
+ PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_BUTTON3 ) PORT_PLAYER(2) /* right select #2 play */
+ PORT_BIT( 0x08, IP_ACTIVE_LOW, IPT_BUTTON4 ) PORT_PLAYER(2) /* right select #3 play */
+ PORT_BIT( 0x10, IP_ACTIVE_LOW, IPT_BUTTON5 ) PORT_PLAYER(2) /* right select #4 play */
+ PORT_BIT( 0x20, IP_ACTIVE_LOW, IPT_BUTTON6 ) PORT_PLAYER(2) /* right select #5 play */
+ PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_BUTTON7 ) PORT_PLAYER(2) /* select two player */
+ PORT_BIT( 0x80, IP_ACTIVE_LOW, IPT_SPECIAL ) /* connects to IPU board */
+
+ PORT_START("ssio:IP3") /* DIPSW @ B3 */
PORT_DIPNAME( 0x01, 0x01, "Coin Meters" )
PORT_DIPSETTING( 0x01, "1" )
PORT_DIPSETTING( 0x00, "2" )
PORT_BIT( 0xfe, IP_ACTIVE_LOW, IPT_UNUSED )
- PORT_START("ssio:IP4") /* J6 1-8 */
+ PORT_START("ssio:IP4") /* J6 1-8 */
PORT_BIT( 0xff, IP_ACTIVE_LOW, IPT_UNUSED )
PORT_START("ssio:DIP")
@@ -1695,7 +1695,7 @@ INPUT_PORTS_END
/* "wiring diagram was not available at time of publication" according to the manual */
/* DIPs verified from the manual */
static INPUT_PORTS_START( demoderb )
- PORT_START("ssio:IP0") /* J4 1-8 */
+ PORT_START("ssio:IP0") /* J4 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_COIN1 )
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_COIN2 )
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_START1 )
@@ -1705,27 +1705,27 @@ static INPUT_PORTS_START( demoderb )
PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_TILT )
PORT_BIT( 0x80, IP_ACTIVE_LOW, IPT_UNUSED )
- PORT_START("ssio:IP1") /* J4 10-13,15-18 */ /* The high 6 bits contain the steering wheel value */
+ PORT_START("ssio:IP1") /* J4 10-13,15-18 */ /* The high 6 bits contain the steering wheel value */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_BUTTON1 ) PORT_PLAYER(1)
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_BUTTON2 ) PORT_PLAYER(1)
- PORT_START("ssio:IP1.ALT1") /* J4 10-13,15-18 */ /* The high 6 bits contain the steering wheel value */
+ PORT_START("ssio:IP1.ALT1") /* J4 10-13,15-18 */ /* The high 6 bits contain the steering wheel value */
PORT_BIT( 0x3f, 0x00, IPT_DIAL ) PORT_SENSITIVITY(50) PORT_KEYDELTA(10) PORT_REVERSE PORT_PLAYER(1)
- PORT_START("ssio:IP1.ALT2") /* IN1 (muxed) -- the high 6 bits contain the steering wheel value */
+ PORT_START("ssio:IP1.ALT2") /* IN1 (muxed) -- the high 6 bits contain the steering wheel value */
PORT_BIT( 0x3f, 0x00, IPT_DIAL ) PORT_SENSITIVITY(50) PORT_KEYDELTA(10) PORT_REVERSE PORT_PLAYER(3)
- PORT_START("ssio:IP2") /* J5 1-8 */ /* The high 6 bits contain the steering wheel value */
+ PORT_START("ssio:IP2") /* J5 1-8 */ /* The high 6 bits contain the steering wheel value */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_BUTTON1 ) PORT_PLAYER(2)
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_BUTTON2 ) PORT_PLAYER(2)
- PORT_START("ssio:IP2.ALT1") /* J5 1-8 */ /* The high 6 bits contain the steering wheel value */
+ PORT_START("ssio:IP2.ALT1") /* J5 1-8 */ /* The high 6 bits contain the steering wheel value */
PORT_BIT( 0x3f, 0x00, IPT_DIAL ) PORT_SENSITIVITY(50) PORT_KEYDELTA(10) PORT_REVERSE PORT_PLAYER(2)
- PORT_START("ssio:IP2.ALT2") /* IN2 (muxed) -- the high 6 bits contain the steering wheel value */
+ PORT_START("ssio:IP2.ALT2") /* IN2 (muxed) -- the high 6 bits contain the steering wheel value */
PORT_BIT( 0x3f, 0x00, IPT_DIAL ) PORT_SENSITIVITY(50) PORT_KEYDELTA(10) PORT_REVERSE PORT_PLAYER(4)
- PORT_START("ssio:IP3") /* DIPSW @ B3 */
+ PORT_START("ssio:IP3") /* DIPSW @ B3 */
PORT_DIPNAME( 0x01, 0x01, DEF_STR( Cabinet ) )
PORT_DIPSETTING( 0x01, "2P Upright" )
PORT_DIPSETTING( 0x00, "4P Cocktail" )
@@ -1745,7 +1745,7 @@ static INPUT_PORTS_START( demoderb )
PORT_DIPSETTING( 0x10, DEF_STR( 1C_2C ) )
PORT_BIT( 0xc0, IP_ACTIVE_LOW, IPT_UNKNOWN )
- PORT_START("ssio:IP4") /* J6 1-8 */
+ PORT_START("ssio:IP4") /* J6 1-8 */
PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_COIN3 )
PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_COIN4 )
PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_START3 )
@@ -1769,8 +1769,8 @@ INPUT_PORTS_END
*************************************/
static GFXDECODE_START( mcr )
- GFXDECODE_SCALE( "gfx1", 0, mcr_bg_layout, 0, 4, 2, 2 ) /* colors 0-15, 2x2 */
- GFXDECODE_ENTRY( "gfx2", 0, mcr_sprite_layout, 0, 4 ) /* colors 16-31 */
+ GFXDECODE_SCALE( "gfx1", 0, mcr_bg_layout, 0, 4, 2, 2 ) /* colors 0-15, 2x2 */
+ GFXDECODE_ENTRY( "gfx2", 0, mcr_sprite_layout, 0, 4 ) /* colors 16-31 */
GFXDECODE_END
@@ -2070,14 +2070,14 @@ ROM_END
ROM_START( dpoker )
- ROM_REGION( 0x10000, "maincpu", 0 )
- ROM_LOAD( "vppp.b3", 0x0000, 0x1000, CRC(2a76ded2) SHA1(3bb5467f0cbca07e72f6d61deb2687b7c1c839c8) )
- ROM_LOAD( "vppp.b4", 0x1000, 0x1000, CRC(d6948faa) SHA1(4b9c3df45b1333c4e5595b790b439c104ab89eda) )
- ROM_LOAD( "vppp.b5", 0x2000, 0x1000, CRC(a49916e5) SHA1(b21268c87bc5c3ea6e072846c5b97a7ae1e3995e) )
- ROM_LOAD( "vppp.d4", 0x3000, 0x1000, CRC(c496934f) SHA1(cf27b6fb764fbf7ed4c5e1030c43498f0ac60c1c) )
- ROM_LOAD( "vppp.d5", 0x4000, 0x1000, CRC(84f4bd38) SHA1(d1c53d8c6ba10d3bc343fe120eecbca70d48b759) )
- ROM_LOAD( "vppp.d6", 0x5000, 0x1000, CRC(b0023bf1) SHA1(77a57a42dd403ef56f334ca295b5b43e94b99598) )
- ROM_LOAD( "vppp.d7", 0x6000, 0x1000, CRC(a4012f5a) SHA1(011e77a6634fbb02a6ae99fe6685c92f2fad3fee) )
+ ROM_REGION( 0x10000, "maincpu", 0 )
+ ROM_LOAD( "vppp.b3", 0x0000, 0x1000, CRC(2a76ded2) SHA1(3bb5467f0cbca07e72f6d61deb2687b7c1c839c8) )
+ ROM_LOAD( "vppp.b4", 0x1000, 0x1000, CRC(d6948faa) SHA1(4b9c3df45b1333c4e5595b790b439c104ab89eda) )
+ ROM_LOAD( "vppp.b5", 0x2000, 0x1000, CRC(a49916e5) SHA1(b21268c87bc5c3ea6e072846c5b97a7ae1e3995e) )
+ ROM_LOAD( "vppp.d4", 0x3000, 0x1000, CRC(c496934f) SHA1(cf27b6fb764fbf7ed4c5e1030c43498f0ac60c1c) )
+ ROM_LOAD( "vppp.d5", 0x4000, 0x1000, CRC(84f4bd38) SHA1(d1c53d8c6ba10d3bc343fe120eecbca70d48b759) )
+ ROM_LOAD( "vppp.d6", 0x5000, 0x1000, CRC(b0023bf1) SHA1(77a57a42dd403ef56f334ca295b5b43e94b99598) )
+ ROM_LOAD( "vppp.d7", 0x6000, 0x1000, CRC(a4012f5a) SHA1(011e77a6634fbb02a6ae99fe6685c92f2fad3fee) )
// The sound board was missing in this pcb set, we'll use the roms from Kick as placeholder.
// Funnily enough, according to a cabinet recording, the sound is actually very similar to Kickman.
@@ -2087,15 +2087,15 @@ ROM_START( dpoker )
ROM_LOAD( "vssp.a9", 0x2000, 0x1000, BAD_DUMP CRC(d1901551) SHA1(fd7d6059f8ac59f95ae6f8ef12fbfce7ed16ec12) )
ROM_LOAD( "vssp.a10", 0x3000, 0x1000, BAD_DUMP CRC(d36ddcdc) SHA1(2d3ec83b9fa5a9d309c393a0c3ee45f0ba8192c9) )
- ROM_REGION( 0x02000, "gfx1", 0 )
- ROM_LOAD( "vpbg.g4", 0x0000, 0x1000, CRC(9fe9aad8) SHA1(f9174bcce3886548b8c18c5a06995d5c69ce5486) )
- ROM_LOAD( "vpbg.g5", 0x1000, 0x1000, CRC(d43aeaae) SHA1(7bbabf9641c73154a769aa9bfc56ab0bc050e964) )
+ ROM_REGION( 0x02000, "gfx1", 0 )
+ ROM_LOAD( "vpbg.g4", 0x0000, 0x1000, CRC(9fe9aad8) SHA1(f9174bcce3886548b8c18c5a06995d5c69ce5486) )
+ ROM_LOAD( "vpbg.g5", 0x1000, 0x1000, CRC(d43aeaae) SHA1(7bbabf9641c73154a769aa9bfc56ab0bc050e964) )
- ROM_REGION( 0x08000, "gfx2", 0 )
- ROM_LOAD( "vpfg.a1", 0x6000, 0x2000, CRC(d76ec7dd) SHA1(a7be6f05a988c59c7f83c640dd0ef824ea4ce839) )
- ROM_LOAD( "vpfg.b1", 0x4000, 0x2000, CRC(cdba9a7d) SHA1(9076b52363cd84ae6e01ac46b369d7719536fac0) )
- ROM_LOAD( "vpfg.d1", 0x2000, 0x2000, CRC(c661cace) SHA1(d5755f0c32a7d9ba283822daaf37ccbd2f6667de) )
- ROM_LOAD( "vpfg.e1", 0x0000, 0x2000, CRC(acb3b469) SHA1(9769d6cfd49cba48264034fb5aed1d1b84ebba4c) )
+ ROM_REGION( 0x08000, "gfx2", 0 )
+ ROM_LOAD( "vpfg.a1", 0x6000, 0x2000, CRC(d76ec7dd) SHA1(a7be6f05a988c59c7f83c640dd0ef824ea4ce839) )
+ ROM_LOAD( "vpfg.b1", 0x4000, 0x2000, CRC(cdba9a7d) SHA1(9076b52363cd84ae6e01ac46b369d7719536fac0) )
+ ROM_LOAD( "vpfg.d1", 0x2000, 0x2000, CRC(c661cace) SHA1(d5755f0c32a7d9ba283822daaf37ccbd2f6667de) )
+ ROM_LOAD( "vpfg.e1", 0x0000, 0x2000, CRC(acb3b469) SHA1(9769d6cfd49cba48264034fb5aed1d1b84ebba4c) )
ROM_END
@@ -2675,7 +2675,7 @@ ROM_START( dotrone )
ROM_LOAD( "loc-b.cp9", 0x0e000, 0x2000, CRC(565a5c48) SHA1(9dfafd58bd552bfda4e1799a175735ecc1369ba3) )
ROM_REGION( 0x0040, "proms", 0 )
- ROM_LOAD( "edotlamp.u2", 0x0020, 0x0020, CRC(fb58b867) SHA1(45beb55f2c2e9197f091fc06e9a2f595e57e5c93) ) /* lamp sequencer PROM */
+ ROM_LOAD( "edotlamp.u2", 0x0020, 0x0020, CRC(fb58b867) SHA1(45beb55f2c2e9197f091fc06e9a2f595e57e5c93) ) /* lamp sequencer PROM */
ROM_END
@@ -2696,7 +2696,7 @@ ROM_START( nflfoot )
ROM_LOAD( "nfl-sqtk-11-15-83.u4", 0x0a000, 0x1000, CRC(b202439b) SHA1(b09e94b0b176f80b12fb4cefa6efd5b2cccb6192) )
ROM_LOAD( "nfl-sqtk-11-15-83.u5", 0x0b000, 0x1000, CRC(bbfe4d39) SHA1(161ed211701e576978d6ef8b9766eb7742a29eb3) )
- ROM_REGION( 0x10000, "ipu", 0 ) /* 64k for the IPU CPU */
+ ROM_REGION( 0x10000, "ipu", 0 ) /* 64k for the IPU CPU */
ROM_LOAD( "ipu-7-9.a2", 0x0000, 0x2000, CRC(0e083adb) SHA1(b799568ff851f7320869fb84821a90eb1156556f) )
ROM_LOAD( "ipu-7-9.a4", 0x2000, 0x2000, CRC(5c9c4764) SHA1(ee9fe1d85dbfb1089bc8ed106a28fe5f3c36fb42) )
@@ -2722,9 +2722,9 @@ ROM_START( demoderb )
ROM_LOAD( "dd_pro1", 0x04000, 0x4000, CRC(4c713bfe) SHA1(493b6ba01e86e7586ad123c53cf7f0a0c191d670) )
ROM_LOAD( "dd_pro2", 0x08000, 0x4000, CRC(c2cbd2a4) SHA1(fa642b2f61ff5529ab688a43c1dc14357a4eba6f) )
- ROM_REGION( 0x10000, "ssio:cpu", ROMREGION_ERASE00 ) /* 64k for the audio CPU, not populated */
+ ROM_REGION( 0x10000, "ssio:cpu", ROMREGION_ERASE00 ) /* 64k for the audio CPU, not populated */
- ROM_REGION( 0x10000, "tcs:cpu", 0 ) /* 64k for the Turbo Cheap Squeak */
+ ROM_REGION( 0x10000, "tcs:cpu", 0 ) /* 64k for the Turbo Cheap Squeak */
ROM_LOAD( "tcs_u5.bin", 0x0c000, 0x2000, CRC(eca33b2c) SHA1(938b021ea3b0f23aed7a98a930a58af371a02303) )
ROM_LOAD( "tcs_u4.bin", 0x0e000, 0x2000, CRC(3490289a) SHA1(a9d56ea60bb901267da41ab408f8e1ed3742b0ac) )