// license:BSD-3-Clause // copyright-holders:Pierpaolo Prazzoli /******************************************************************** Pasha Pasha 2 Dong Sung, 1998 3PLAY |--------------------------------------------------| | DA1311 UM53 AD-65 DREAM 9.6MHz | |KA22065 TL062 UM51 AD-65 RESET_SW | | VOL1 VOL2 1MHz TL7705 | | | | DSW2(8) 20MHz GM71C18163 | | 93C46 UM2 | | PAL | |J | |A | |M E1-16XT AT89C52| |M | |A U102 | | 6116 | | 6116 U3 U101 | | | | | | 12MHz| | A42MX16 | | DSW1(8) | | UCN5801 | | UCN5801 | | 16MHz | |--------------------------------------------------| Notes: U3 - 27C040 EPROM (DIP32) UM2/UM51/53- 29F040 EPROM (PLCC32) U101/102 - Each location contains a small adapter board plugged into a DIP42 socket. Each adapter board holds 2x Intel E28F016S5 TSOP40 16M FlashROMs. On the PCB under the ROMs it's marked '32MASK'. However, the adapter boards are not standard. If you try to read the ROMs while they are _ON-THE-ADAPTER_ as a 32M DIP42 EPROM (such as 27C322), the FlashROMs are damaged and the PCB no longer works :( Thus, the FlashROMs must be removed and read separately! The small adapter boards with their respective FlashROMs are laid out like this........ |------------------------------| | | | U2 U1 | U102 | | |------------------------------| |------------------------------| | | | U2 U1 | U101 | | |------------------------------| A42MX16 - Actel A42MX16 FPGA (QFP160) AT89C52 - Atmel AT89C52 Microcontroller w/8k internal FlashROM, clock 12MHz (DIP40) E1-16XT - Hyperstone E1-16XT CPU, clock 20MHz DREAM - ATMEL DREAM SAM9773 Single Chip Synthesizer/MIDI with Effects and Serial Interface, clock 9.6MHz (TQFP80) AD-65 - Oki compatible M6295 sound chip, clock 1MHz 5493R45 - ISSI 5493R45-001 128k x8 SRAM (SOJ32) GM71C18163 - Hynix 1M x16 DRAM (SOJ42) VSync - 60Hz HSync - 15.15kHz driver by Pierpaolo Prazzoli TODO: - eeprom - is it used? - irq2 - sound related? reads the 2 unmapped input registers. - irq3 - it only writes a 0 into memory and changes a register - pasha2: simulate music (DREAM chip) - zdrum: with DRC it fatal errors with 'Unimplemented: generate_adds (c00013ae)' if let in attract for a while or at the end of the 'Flash memory check' in test mode) with interpreter the game hangs itself with 'Assertion failed: file flash.dat' - zdrum: proper inputs (coin seems to freeze the game - gets stuck in a loop at c0001386, can be forced out of it with do PC=c0001392 and the coin gets credited) - right arrow not found yet, second left drum switch flickers on and off continuously in i/o test) - zdrum: when coined up via debugger and then started, the game itself reports an assert with DRC, gets to the select character screen and then hangs with the interpreter - zdrum: settings aren't kept after reset, possibly needs eeprom hook up - zdrum: dump hard disc and emulate MP3 board *********************************************************************/ #include "emu.h" #include "cpu/mcs51/mcs51.h" #include "cpu/e132xs/e132xs.h" #include "machine/eepromser.h" #include "sound/okim6295.h" #include "emupal.h" #include "screen.h" #include "speaker.h" #include "pasha2.lh" class pasha2_state : public driver_device { public: pasha2_state(const machine_config &mconfig, device_type type, const char *tag) : driver_device(mconfig, type, tag) , m_wram(*this, "wram") , m_mainbank(*this, "mainbank") , m_lamps_r(*this, "lamp_p%u_r", 1U) , m_lamps_g(*this, "lamp_p%u_g", 1U) , m_lamps_b(*this, "lamp_p%u_b", 1U) , m_maincpu(*this, "maincpu") , m_oki(*this, "oki%u", 1U) , m_palette(*this, "palette") { } void pasha2(machine_config &config); void zdrum(machine_config &config); void init_pasha2(); protected: virtual void machine_start() override; virtual void machine_reset() override; virtual void video_start() override; private: // memory pointers required_shared_ptr m_wram; required_memory_bank m_mainbank; // output finders output_finder<3> m_lamps_r; output_finder<3> m_lamps_g; output_finder<3> m_lamps_b; // devices required_device m_maincpu; required_device_array m_oki; required_device m_palette; // video-related u8 m_vbuffer = 0; bitmap_ind16 m_bg_bitmap[2]; bitmap_ind16 m_fg_bitmap[2]; // video functions void vbuffer_set_w(u16 data); void vbuffer_clear_w(u16 data); void bg_bitmap_w(offs_t offset, u8 data); void fg_bitmap_w(offs_t offset, u8 data); u32 screen_update(screen_device &screen, bitmap_ind16 &bitmap, const rectangle &cliprect); // peripheral handlers template void oki_bank_w(offs_t offset, u16 data); void misc_w(offs_t offset, u16 data); void pasha2_lamps_w(u16 data); // speedup functions u16 pasha2_speedup_r(offs_t offset); // address maps void pasha2_io(address_map &map); void pasha2_map(address_map &map); void zdrum_audio_map(address_map &map); }; void pasha2_state::misc_w(offs_t offset, u16 data) { if (offset) { if (data & 0x0800) { const u16 bank = data & 0xf000; switch (bank) { case 0x8000: case 0x9000: case 0xa000: case 0xb000: case 0xc000: case 0xd000: m_mainbank->set_entry((bank>>12) & 7); break; } } } } void pasha2_state::vbuffer_set_w(u16 data) { m_vbuffer = 1; } void pasha2_state::vbuffer_clear_w(u16 data) { m_vbuffer = 0; } void pasha2_state::bg_bitmap_w(offs_t offset, u8 data) { m_bg_bitmap[m_vbuffer].pix(offset >> 9, offset & 0x1ff) = (data & 0xff) | 0x100; } void pasha2_state::fg_bitmap_w(offs_t offset, u8 data) { // handle overlapping pixels without writing them if ((data & 0xff) == 0xff) return; m_fg_bitmap[m_vbuffer].pix(offset >> 9, offset & 0x1ff) = data & 0xff; } template void pasha2_state::oki_bank_w(offs_t offset, u16 data) { if (offset) m_oki[Chip]->set_rom_bank(data & 1); } void pasha2_state::pasha2_lamps_w(u16 data) { for (int p = 0; p < 3; p++) { m_lamps_r[p] = BIT(data, (p << 2) | 0); m_lamps_g[p] = BIT(data, (p << 2) | 1); m_lamps_b[p] = BIT(data, (p << 2) | 2); } } void pasha2_state::pasha2_map(address_map &map) { // MEM0 (DRAM) map(0x00000000, 0x001fffff).ram().share("wram"); // MEM1 (VRAM and Video registers) map(0x40000000, 0x4001ffff).ram().w(FUNC(pasha2_state::bg_bitmap_w)); map(0x40020000, 0x4003ffff).ram().w(FUNC(pasha2_state::fg_bitmap_w)); map(0x40060000, 0x40060001).nopw(); map(0x40064000, 0x40064001).nopw(); map(0x40068000, 0x40068001).nopw(); map(0x4006c000, 0x4006c001).nopw(); map(0x40070000, 0x40070001).w(FUNC(pasha2_state::vbuffer_clear_w)); map(0x40074000, 0x40074001).w(FUNC(pasha2_state::vbuffer_set_w)); map(0x40078000, 0x40078001).nopw(); //once at startup -> to disable the eeprom? // MEM2 (Bankswitched ROM) map(0x80000000, 0x803fffff).bankr("mainbank"); // MEM3 (Palette, Boot ROM) map(0xe0000000, 0xe00001ff).rw(m_palette, FUNC(palette_device::read8), FUNC(palette_device::write8)).share("palette"); //tilemap? palette? map(0xe0000200, 0xe00003ff).rw(m_palette, FUNC(palette_device::read8_ext), FUNC(palette_device::write8_ext)).share("palette_ext"); // " map(0xfff80000, 0xffffffff).rom().region("maincpu", 0); } void pasha2_state::pasha2_io(address_map &map) { map(0x08, 0x0b).nopr(); //sound status? map(0x18, 0x1b).nopr(); //sound status? map(0x20, 0x23).w(FUNC(pasha2_state::pasha2_lamps_w)); map(0x40, 0x43).portr("COINS"); map(0x60, 0x63).portr("DSW"); map(0x80, 0x83).portr("INPUTS"); map(0xa0, 0xa3).nopw(); //soundlatch? map(0xc0, 0xc3).w(FUNC(pasha2_state::misc_w)); map(0xe3, 0xe3).rw(m_oki[0], FUNC(okim6295_device::read), FUNC(okim6295_device::write)); map(0xe7, 0xe7).rw(m_oki[1], FUNC(okim6295_device::read), FUNC(okim6295_device::write)); map(0xe8, 0xeb).w(FUNC(pasha2_state::oki_bank_w<0>)); map(0xec, 0xef).w(FUNC(pasha2_state::oki_bank_w<1>)); } void pasha2_state::zdrum_audio_map(address_map &map) { map(0x00000000, 0x001fffff).ram(); map(0xfff80000, 0xffffffff).rom().region("audiocpu", 0); } static INPUT_PORTS_START( pasha2 ) PORT_START("COINS") PORT_BIT( 0x0001, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x0002, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x0004, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x0008, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x0010, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x0020, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x0040, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x0080, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x0100, IP_ACTIVE_LOW, IPT_COIN1 ) PORT_BIT( 0x0200, IP_ACTIVE_LOW, IPT_COIN2 ) PORT_BIT( 0x0400, IP_ACTIVE_LOW, IPT_COIN3 ) PORT_BIT( 0x0800, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x1000, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x2000, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x4000, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x8000, IP_ACTIVE_LOW, IPT_UNKNOWN ) // 2 physical dip-switches PORT_START("DSW") PORT_DIPNAME( 0x0001, 0x0001, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x0001, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x0002, 0x0002, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x0002, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x0004, 0x0004, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x0004, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x0018, 0x0008, DEF_STR( Lives ) ) PORT_DIPSETTING( 0x0018, "1" ) PORT_DIPSETTING( 0x0010, "2" ) PORT_DIPSETTING( 0x0008, "3" ) PORT_DIPSETTING( 0x0000, "5" ) PORT_DIPNAME( 0x0060, 0x0060, DEF_STR( Coinage ) ) PORT_DIPSETTING( 0x0000, DEF_STR( 5C_1C ) ) PORT_DIPSETTING( 0x0020, DEF_STR( 3C_1C ) ) PORT_DIPSETTING( 0x0040, DEF_STR( 2C_1C ) ) PORT_DIPSETTING( 0x0060, DEF_STR( 1C_1C ) ) PORT_DIPNAME( 0x0080, 0x0080, DEF_STR( Free_Play ) ) PORT_DIPSETTING( 0x0080, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x0100, 0x0100, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x0100, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x0200, 0x0200, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x0200, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x0400, 0x0400, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x0400, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x0800, 0x0800, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x0800, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x1000, 0x1000, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x1000, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x2000, 0x2000, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x2000, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x4000, 0x4000, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x4000, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x8000, 0x8000, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x8000, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_START("INPUTS") PORT_BIT( 0x0001, IP_ACTIVE_LOW, IPT_BUTTON1 ) PORT_PLAYER(1) PORT_BIT( 0x0002, IP_ACTIVE_LOW, IPT_BUTTON2 ) PORT_PLAYER(1) PORT_BIT( 0x0004, IP_ACTIVE_LOW, IPT_BUTTON3 ) PORT_PLAYER(1) PORT_BIT( 0x0008, IP_ACTIVE_LOW, IPT_START1 ) PORT_BIT( 0x0010, IP_ACTIVE_LOW, IPT_BUTTON1 ) PORT_PLAYER(2) PORT_BIT( 0x0020, IP_ACTIVE_LOW, IPT_BUTTON2 ) PORT_PLAYER(2) PORT_BIT( 0x0040, IP_ACTIVE_LOW, IPT_BUTTON3 ) PORT_PLAYER(2) PORT_BIT( 0x0080, IP_ACTIVE_LOW, IPT_START2 ) PORT_BIT( 0x0100, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x0200, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x0400, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x0800, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x1000, IP_ACTIVE_LOW, IPT_BUTTON1 ) PORT_PLAYER(3) PORT_BIT( 0x2000, IP_ACTIVE_LOW, IPT_BUTTON2 ) PORT_PLAYER(3) PORT_BIT( 0x4000, IP_ACTIVE_LOW, IPT_BUTTON3 ) PORT_PLAYER(3) PORT_BIT( 0x8000, IP_ACTIVE_LOW, IPT_START3 ) INPUT_PORTS_END static INPUT_PORTS_START( zdrum ) PORT_START("COINS") // no apparent effects on gameplay or i/o test, but for otherwise noted PORT_BIT( 0x0001, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x0002, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x0004, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x0008, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x0010, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x0020, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x0040, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x0080, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x0100, IP_ACTIVE_LOW, IPT_COIN1 ) // coin, but game enters a loop when pressed PORT_BIT( 0x0200, IP_ACTIVE_LOW, IPT_SERVICE1 ) // service in i/o test, seems to have no effect during gameplay PORT_BIT( 0x0400, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_SERVICE_NO_TOGGLE( 0x800, IP_ACTIVE_LOW ) PORT_BIT( 0x2000, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x4000, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x8000, IP_ACTIVE_LOW, IPT_UNKNOWN ) // 2 physical dip-switches, but the settings seem to be done via service mode, so possibly unused? PORT_START("DSW") PORT_DIPNAME( 0x0001, 0x0001, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x0001, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x0002, 0x0002, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x0002, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x0004, 0x0004, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x0004, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x0008, 0x0008, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x0008, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x0010, 0x0010, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x0010, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x0020, 0x0020, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x0020, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x0040, 0x0040, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x0040, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x0080, 0x0080, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x0080, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x0100, 0x0100, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x0100, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x0200, 0x0200, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x0200, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x0400, 0x0400, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x0400, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x0800, 0x0800, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x0800, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x1000, 0x1000, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x1000, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x2000, 0x2000, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x2000, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x4000, 0x4000, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x4000, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_DIPNAME( 0x8000, 0x8000, DEF_STR( Unknown ) ) PORT_DIPSETTING( 0x8000, DEF_STR( Off ) ) PORT_DIPSETTING( 0x0000, DEF_STR( On ) ) PORT_START("INPUTS") PORT_BIT( 0x0001, IP_ACTIVE_LOW, IPT_BUTTON6 ) PORT_PLAYER(1) PORT_NAME( "Drum switch right 2" ) PORT_BIT( 0x0002, IP_ACTIVE_LOW, IPT_BUTTON4 ) PORT_PLAYER(1) // TODO: what's up with this? should probably be // PORT_NAME( "Drum switch left 3" ), but it flickers on and off regardless PORT_BIT( 0x0004, IP_ACTIVE_LOW, IPT_BUTTON2 ) PORT_PLAYER(1) PORT_NAME( "Drum switch left 1" ) PORT_BIT( 0x0008, IP_ACTIVE_LOW, IPT_BUTTON3 ) PORT_PLAYER(1) PORT_NAME( "Drum switch left 2" ) PORT_BIT( 0x0010, IP_ACTIVE_LOW, IPT_BUTTON7 ) PORT_PLAYER(1) PORT_NAME( "Drum switch right 3" ) PORT_BIT( 0x0020, IP_ACTIVE_LOW, IPT_BUTTON5 ) PORT_PLAYER(1) PORT_NAME( "Drum switch right 1" ) PORT_BIT( 0x0040, IP_ACTIVE_LOW, IPT_BUTTON1 ) PORT_PLAYER(1) PORT_NAME( "Left arrow" ) PORT_BIT( 0x0080, IP_ACTIVE_LOW, IPT_START1 ) PORT_BIT( 0x0100, IP_ACTIVE_LOW, IPT_UNKNOWN ) // all the following but 0x800 don't seem to have any effect PORT_BIT( 0x0200, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x0400, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x0800, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x1000, IP_ACTIVE_LOW, IPT_JOYSTICK_DOWN ) // isn't shown in the i/o test but it's used to move between items in the service mode PORT_BIT( 0x2000, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x4000, IP_ACTIVE_LOW, IPT_UNKNOWN ) PORT_BIT( 0x8000, IP_ACTIVE_LOW, IPT_UNKNOWN ) INPUT_PORTS_END void pasha2_state::video_start() { // 2 512x256 8bpp bitmaps, Both are double buffered for (int i = 0; i < 2; i++) { m_bg_bitmap[i].allocate(512, 256); m_fg_bitmap[i].allocate(512, 256); m_bg_bitmap[i].fill(0x100); // Palette space 0x100-0x1ff m_fg_bitmap[i].fill(0); // Palette space 0x000-0x0ff save_item(NAME(m_bg_bitmap[i]), i); save_item(NAME(m_fg_bitmap[i]), i); } } u32 pasha2_state::screen_update(screen_device &screen, bitmap_ind16 &bitmap, const rectangle &cliprect) { copybitmap(bitmap, m_bg_bitmap[(m_vbuffer ^ 1)], 0, 0, 0, 0, cliprect); copybitmap_trans(bitmap, m_fg_bitmap[(m_vbuffer ^ 1)], 0, 0, 0, 0, cliprect, 0); return 0; } void pasha2_state::machine_start() { m_lamps_r.resolve(); m_lamps_g.resolve(); m_lamps_b.resolve(); m_mainbank->configure_entries(0, 6, memregion("bankeddata")->base(), 0x400000); m_mainbank->set_entry(0); save_item(NAME(m_vbuffer)); } void pasha2_state::machine_reset() { m_vbuffer = 0; } void pasha2_state::pasha2(machine_config &config) { // basic machine hardware E116XT(config, m_maincpu, 20_MHz_XTAL*4); // 4x internal multiplier m_maincpu->set_addrmap(AS_PROGRAM, &pasha2_state::pasha2_map); m_maincpu->set_addrmap(AS_IO, &pasha2_state::pasha2_io); m_maincpu->set_vblank_int("screen", FUNC(pasha2_state::irq0_line_hold)); AT89C52(config, "audiocpu", 12_MHz_XTAL); // clock from docs // TODO : ports are unimplemented; P0,P1,P2,P3 and Serial Port Used EEPROM_93C46_16BIT(config, "eeprom"); // video hardware screen_device &screen(SCREEN(config, "screen", SCREEN_TYPE_RASTER)); screen.set_refresh_hz(60); screen.set_vblank_time(ATTOSECONDS_IN_USEC(0)); screen.set_size(512, 512); screen.set_visarea(0, 383, 0, 239); screen.set_screen_update(FUNC(pasha2_state::screen_update)); screen.set_palette(m_palette); PALETTE(config, m_palette).set_format(palette_device::xBGR_555, 0x200); m_palette->set_membits(8); // sound hardware SPEAKER(config, "mono").front_center(); OKIM6295(config, m_oki[0], 1_MHz_XTAL, okim6295_device::PIN7_HIGH).add_route(ALL_OUTPUTS, "mono", 1.0); OKIM6295(config, m_oki[1], 1_MHz_XTAL, okim6295_device::PIN7_HIGH).add_route(ALL_OUTPUTS, "mono", 1.0); //and ATMEL DREAM SAM9773 } void pasha2_state::zdrum(machine_config &config) { pasha2(config); m_maincpu->set_force_no_drc(true); // gets a bit further e116xt_device &audiocpu(E116XT(config.replace(), "audiocpu", 45_MHz_XTAL)); // type unknown, but it does look like Hyperstone code audiocpu.set_addrmap(AS_PROGRAM, &pasha2_state::zdrum_audio_map); // TODO: MP3 hw, also PCB should be stereo according to test mode } ROM_START( pasha2 ) ROM_REGION16_BE( 0x80000, "maincpu", 0 ) // Hyperstone CPU Code ROM_LOAD( "pp2.u3", 0x00000, 0x80000, CRC(1c701273) SHA1(f465323a1d3f2fd752c51c178fafe4cc866e28d6) ) ROM_REGION16_BE( 0x400000*6, "bankeddata", ROMREGION_ERASEFF ) // data roms ROM_LOAD16_BYTE( "pp2-u2.u101", 0x000000, 0x200000, CRC(85c4a2d0) SHA1(452b24b74bd0b65d2d6852486e2917f94e21ecc8) ) ROM_LOAD16_BYTE( "pp2-u1.u101", 0x000001, 0x200000, CRC(96cbd04e) SHA1(a4e7dd61194584b3c4217674d78ab2fd96b7b2e0) ) ROM_LOAD16_BYTE( "pp2-u2.u102", 0x400000, 0x200000, CRC(2097d88c) SHA1(7597578e6ddca00909feac35d9d7331f783b2bd6) ) ROM_LOAD16_BYTE( "pp2-u1.u102", 0x400001, 0x200000, CRC(7a3492fb) SHA1(de72c4d10e17eaf2b7531f637b42cbb3d07819b5) ) // empty space, but no empty sockets on the pcb ROM_REGION( 0x2000, "audiocpu", 0 ) // AT89C52 ROM_LOAD( "89c52.bin", 0x0000, 0x2000, CRC(9ce43ce4) SHA1(8027a3549b38e9a2e7bb8f518a0defcaf9743371) ) // music play 1.0 ROM_REGION( 0x80000, "sam9773", 0 ) // SAM9773 sound data ROM_LOAD( "pp2.um2", 0x00000, 0x80000, CRC(86814b37) SHA1(70f8a94410e362669570c39e00492c0d69de6b17) ) ROM_REGION( 0x80000, "oki1", 0 ) // Oki Samples ROM_LOAD( "pp2.um51", 0x00000, 0x80000, CRC(3b1b1a30) SHA1(1ea1266d280a2b96ac4ef9fe8ee7b1a5f7861672) ) ROM_REGION( 0x80000, "oki2", 0 ) // Oki Samples ROM_LOAD( "pp2.um53", 0x00000, 0x80000, CRC(8a29ad03) SHA1(3e9b0c86d8e3bb0b7691f68ad45431f6f9e8edbd) ) ROM_END // PARA8B16 main PCB, very similar to the Pasha Pasha 2 PCB but with no AT89C52 and SAM9773 // PARA MP3 MAIN Ver. 1.00 2000.1 plug in PCB (Xilinx XC9536, Micronas MAS3507D F10, Micronas DAC3550A C2, 14.7456 XTAL) // MUTALISK V3.02 PCB which plugs in the MP3 PCB (stickered IC 'Catos Creative Staffs' - probably an Hyperstone core given the ROM content -, 45.0000000 MHz XTAL, GM71V65163CT5 RAM, D27C040 ROM) ROM_START( zdrum ) ROM_REGION16_BE( 0x80000, "maincpu", 0 ) // Hyperstone CPU Code ROM_LOAD( "u3.bin", 0x00000, 0x80000, CRC(296c6ee8) SHA1(67814ac87828f578591ec2069ad96861fe29de6c) ) ROM_REGION16_BE( 0x400000*6, "bankeddata", ROMREGION_ERASEFF ) // data roms ROM_LOAD16_WORD_SWAP( "u101.bin", 0x000000, 0x400000, CRC(e9bc892e) SHA1(f50cde278693a38cfad1185a89c41e2e2029c5ac) ) // Dumped as 27C322, but actually E28F916S5 * 2 ROM_LOAD16_WORD_SWAP( "u102.bin", 0x400000, 0x400000, CRC(954e67a1) SHA1(cf1553fd70e27fab2d77df07ccd2866c198b5b35) ) // " ROM_REGION( 0x80000, "audiocpu", 0 ) // on the MUTALISK PCB ROM_LOAD( "mutalisk_u6.bin", 0x00000, 0x80000, CRC(7d044372) SHA1(41c63644ce048cec2079fb5ec8a2da9c66841c48) ) // 27C4000DC ROM_REGION( 0x80000, "oki1", 0 ) ROM_LOAD( "um51.bin", 0x00000, 0x80000, CRC(b1a22ea2) SHA1(2814d212faf99504bd19602c4183fd8a4763c44c) ) // AM29F040 ROM_REGION( 0x80000, "oki2", 0 ) ROM_LOAD( "um53.bin", 0x00000, 0x80000, CRC(372022da) SHA1(809d103bdb365c9ff9e32b6a3032040b6a91ce88) ) // MBM29F040A ROM_REGION( 0x117, "plds", 0 ) ROM_LOAD( "u507.bin", 0x000, 0x117, CRC(681ddf27) SHA1(0f9696918e512eb3840750c9386b4312a9e937ab) ) // PALCE16V8H DISK_REGION( "ide:0:hdd:image" ) // should contain the songs DISK_IMAGE( "zdrum", 0, NO_DUMP ) ROM_END u16 pasha2_state::pasha2_speedup_r(offs_t offset) { if(m_maincpu->pc() == 0x8302) m_maincpu->spin_until_interrupt(); return m_wram[(0x95744 / 2) + offset]; } void pasha2_state::init_pasha2() { m_maincpu->space(AS_PROGRAM).install_read_handler(0x95744, 0x95747, read16sm_delegate(*this, FUNC(pasha2_state::pasha2_speedup_r))); } GAMEL( 1998, pasha2, 0, pasha2, pasha2, pasha2_state, init_pasha2, ROT0, "Dong Sung", "Pasha Pasha 2", MACHINE_IMPERFECT_SOUND | MACHINE_SUPPORTS_SAVE, layout_pasha2 ) GAME ( 2000, zdrum, 0, zdrum, zdrum, pasha2_state, empty_init, ROT0, "PARA Enterprises", "Zooty Drum", MACHINE_NOT_WORKING | MACHINE_IMPERFECT_SOUND | MACHINE_SUPPORTS_SAVE ) // missing HD dump, MP3 board emulation. Inputs seem to be read differently.